As an Original Equipment Supplier, Delphi Automotive products from 1A Auto come directly from the source. You wont have to worry about going to the dealership for Original Equipment - these parts are the exact same as the original. Delphi products come with the same quality from the dealership at a lower cost to you.
Install Tip: You may be required to reset the vehicle computer after installation of this part.
Direct Fit Replacement - Guaranteed to fit and function for your specific application Quality Tested - built to a strict level of product standards.
Item Condition:New
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Install Replace Mass Air Flow MAF Sensor 2009-12 Chevy Suburban
How To Replace Mass Air Flow Sensor 2009-12 Chevy Silverado
Created on:
Tools used
T15 Torx Driver
1. Removing the MAF Sensor
Disconnect the wiring harness
Remove the two T-15 Torx screws from the sensor
Remove the sensor
2. Installing the MAF Sensor
Insert the MAF sensor into place
Tighten the two T-15 Torx screws to the sensor
Connect the wiring harness
Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years. We're dedicated to delivering quality auto parts, expert customer service, fast and free shipping, all backed by our 100% satisfaction guarantee. Visit us at 1AAuto.com, your trusted source for quality auto parts.
We're going to remove the mass air flow sensor. It's right here off the air box air cleaner assembly. Start by unplugging it. Place that aside. This is a T-15 Torx screw. Make sure you grab those screws so you don't drop them. Just pop this out. It's got a little seal on it. It'll come right out.
This is the old mass air flow sensor. It's got five pins in there. This is the new one. Five pins. Virtually identical. These are your heating elements and sensing elements in here. You don't want to touch those. Just leave them alone. It's got the O-ring in here that's going to seal on the intake tube. This should fit right in.
We're going to install our new one. It does have a key here and a key here. It also has an arrow in the direction of airflow. You just want to make sure that this arrow is pointing towards the engine, 'cause otherwise this key way shouldn't let you install it, but you don't want to try to force it. That should seat right in there on the O-ring. You'll feel it seat right in there. You got your screws, T-15 Torx, just have a very light Torx. Basically hand tight, 'cause they're just screws in the plastic. To complete it, just plug the harness back in.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
T15 Torx Driver
1. Removing the Mass Air Flow Sensor
Disconnect the mass air flow sensor
Remove the two T15 screws on the sensor
Remove the air flow sensor
2. Installing the New Mass Air Flow Sensor
Insert the air flow sensor into place
Insert the two T15 Torx screws to the sensor
Connect the air flow sensor wiring harness
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the mass airflow sensor on this 2011Chevy Silverado 1500. The only tool you'll need is a T15 bit and a ratchet or a T15 driver would also work.
Your mass airflow sensor is right here on this air intake hose. You just want to push the tab on the bottom of that connector and pull it free, and then remove the two T15 screws on either side of the airflow sensor. Once removed, the sensor just lifts right up and out.
Now you just push your new airflow sensor down into place, and you replace those two T15 screws. Reconnect the harness to the mass airflow sensor, and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
AF10060
In Stock
Product Reviews
Loading reviews
5.00/ 5.04
4 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
4
0
0
0
0
Mass air sensor
mark
February 25, 2019
Easy to install worked great
The best
C
December 22, 2020
Hands down cant go wrong with Delphi products best on the market
Miguel
October 8, 2021
Muy bueno
Raymond
June 8, 2023
Easy to install works great
Customer Q&A
How do you reset your computer?March 22, 2022
Carl E
10
Remove the ground cable from your battery for a minimum of 10 minutes to reset.
March 22, 2022
S K
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Chevrolet is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by Chevrolet or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.