How Replace your Engines Oil 2007-12 Dodge Caliber
Created on: 2013-12-31
Need to change the oil? This video will show you what tools are needed and what's required to get the job done yourself
-
step 1 :Draining the Oil
- Raise the vehicle on jack stands
- Place a drain pan underneath the drain
- Remove the 16mm bolt from the drain
- Drain the oil
- Replace and tighten the 16mm bolt
-
step 2 :Removing the Oil Filter
- Remove the oil filter with an oil filter wrench
- Clean the area with a rag
-
step 3 :Installing the Oil Filter
- Place a layer of oil around the rim of the oil filter
- Twist the oil filter into place
-
step 4 :Servicing the Oil
- Remove the oil cap
- Place a funnel into the oil fill
- Replace the oil to the recommended amount
- Replace the oil cap
- Start the vehicle
- Turn the vehicle off
- Check the oil level with the dipstick
-
step 5 :Turning off the Oil Light
- Put the key in the ignition
- Turn the key forward
- Pump the gas pedal three times
Tools needed
-
Funnel
Oil Filter Wrench
16mm Socket
Jack Stands
Drain Pan
Ratchet
Cloth Rags
Floor Jack
Engine Oil
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to do an oil change on this 2008 Dodge Caliber with a 2-liter engine. The items you'll need for this is a 16mm socket and ratchet, an oil filter wrench, a drip pan, a rag, jack and jack stands, oil, oil filter, and a funnel.
Raise the vehicle and secure it with jack stands. Your drain plug is right here on the center of your oil pan. Use a 16mm wrench to remove it. Make sure you have a drip pan underneath, and just let all your oil drain out. Once it stops coming out, replace that drain plug and just tighten it back up.
To the left of your drain pan is an oil filter. Use an oil filter wrench to break it loose, and then just twist it out the rest of the way. You do want to make sure you have a drip pan underneath it because there is some oil behind that filter. Use a rag to clean up the area.
Take your new oil filter and some fresh oil, and just wipe around the ring. Then twist your new oil filter up into place. Go until it stops spinning that's when the gasket seats. Then tighten it another 1/2 to 3/4 of a turn.
Now remove your oil fill cap and, using a funnel, replace the oil. You can find in your user manual how much oil and what type of oil your vehicle needs. This one called for 5W30 and 4 1/2 quarts. Now remove the funnel and replace your fill cap. Then you want to start the vehicle and let it run for a second. Then pull out your dip stick, wipe it clean, push it all the way back in, pull it out again and check. Ours is right where it needs to be.
Now, when you start your vehicle after a second, you'll still see that change oil message pop up, right there. To get that message to stop, you just want to put the key in and turn it forward like you're going to start the vehicle and pump the gas pedal three times. That will reset that.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
How To Change Oil 2000-06 GMC Sierra 2500HD 6-0L
Learn how to change the oil in your 00-06 GMC Sierra 2500 HD with the 6.0L engine.
