How to Change Oil 2002-08 Dodge Ram 1500 5-7l Hemi
Created on: 2016-06-14
Time for an oil change! Don't over pay at the dealer, or risk half hearted work at a quick place! Do it yourself! Learn how in this video from 1A Auto!
-
step 1 :Draining the Oil
- Raise the vehicle on jack stands
- Have a drain pan ready
- Remove the 13mm bolt from the drain
- Drain the oil
- Twist on the 13mm drain bolt
- Tighten the bolt with a 13mm wrench or socket and ratchet
- Torque the drain plug to 25 foot-pounds
-
step 2 :Removing the Oil Filter
- Have a drain pan ready
- Remove the oil filter with an oil filter wrench
- Clean the area with a rag
- Make sure there is no gasket left behind
-
step 3 :Installing the Oil Filter
- Place a layer of oil around the rim of the oil filter
- Twist the oil filter into place
-
step 4 :Servicing the Oil
- Remove the oil cap
- Place a funnel into the oil fill
- Replace the oil to the recommended amount
- Replace the oil cap
- Start the vehicle
- Turn the vehicle off
- Check the oil level with the dipstick
Tools needed
-
Funnel
13mm Socket
Oil Filter Wrench
Torque Wrench
Drain Pan
Ratchet
Cloth Rags
Engine Oil
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to do an oil change in this 2008 Dodge Ram. This one has the 5.7-liter Hemi in it. You'll need a drain pan, 13 millimeter socket and ratchet, a rag, torque wrench, strap wrench, funnel, new oil, and a new oil filter.
Open your hood and locate your oil fill cap, unscrew it, and place it off to the side. You don't have to raise and support your vehicle to do this job, but we did it to make it a little bit easier to show you. Unscrew the 13 millimeter drain plug with a socket and ratchet. Be sure to have a drain bucket positioned under your oil pan. Allow the oil the drain. Wipe off any dirt and debris from the threads and gasket of your drain plug and the surface of the pan, reinstall your drain plug, and torque it to 25 foot-pounds.
The oil filter is located on the passenger side of the engine just behind the harmonic balancer and bottom radiator hose. Place your strap wrench around the oil filter and unscrew it. After a couple turns with the strap wrench, you should be able to do the rest by hand. Be sure to have a drain bucket underneath the filter. Once it's cracked loose, allow it to drain. When the oil filter's finished draining, unscrew it the rest of the way and place it upside down in your drain bucket. Check the surface to be sure that the gasket from your oil filter came out and didn't stick to the motor.
Using some new oil lubricate the gasket on your new oil filter, spin it back onto the engine. Get it on as tight as you can by hand. Once there's oil in the motor, start it up and check the filter for leaks. Place a funnel into the oil fill. This motor takes 7 quarts of 520 oil, but always check the specifications for your exact vehicle.
Remove the funnel, reinstall your oil cap, start the truck, watch for the oil pressure gauge to come up to center so you know the vehicle has built pressure throughout the system. Once the vehicle has reached normal oil pressure, then shut it off. After you allow the vehicle to sit for a few seconds after shutting it off so the oil drains back into the pan, remove your dipstick, wipe it off, reinstall it fully into the tube, remove it again, check your oil level.
New oil's a little harder to see on the dipstick, then darker used oil is so make sure you check and you see a color difference up through the hash marks all the way to the right side here so you know your level's full. Anything lower top off the oil accordingly until you've reached the full mark.
Like most newer vehicles, our 2008 Ram has an indicator light on the dash to let us know it's time to change our oil. After you've done your oil change to reset it at home, turn the key to the run position one click before actually starting it. To press the gas pedal three times fully within 10 seconds. Turn the key to run and within 10 seconds fully, depress the gas pedal three times, shut the key off, turn it back on to verify that our change oil light has gone away.
To ensure the longevity of your car's engine, be sure to do the oil change per the manufacturer's specifications. This can be found in the owner's manual of your vehicle. Use the proper weight and type of oil be it conventional blend or full synthetic. Be sure to check your oil level at least once a week to make sure that the engine is free of leaks or burning oil. Keep that level up top and your engine running smooth.
Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.
Quick Fix to Get Rid of a Smell Coming From the Air Conditioning Vents in Your Car or Truck
Sue shows you how leaves, pine needles, and debris collect in the AC evaporator, creating those damp smells.
