How To Remove Door Panel 2002-06 Toyota Camry
Created on: 2011-06-03
Watch this video to learn how to remove and replace the interior door panel on your 02-06 Toyota Camry.
-
step 1 :Removing the Door Panel
- Pry out the door handle trim piece
- Remove the Phillips screw in the door handle
- Pry up the trim piece inside the door pull
- Remove the Phillips screw in the door pull
- Pry off the trim button in the top right corner of the door panel
- Remove the Phillips screw
- Pry up the master switch panel
- Disconnect the master switch panel wiring harness
- Remove the two Phillips screws on the bottom of the door panel
- Remove the Phillips screw in the door panel, behind where the switch panel was
- Pull out around the door panel
- Pry off the sail panel
- Remove the door panel
- Disconnect the door handle and lock cables
-
step 2 :Installing the Door Panel
- Connect the door handle and lock cables
- Insert the door panel into place
- Push the door panel pins into place
- Tighten the Phillips screw in the door panel, behind where the switch panel was
- Insert the Phillips screw in the top right corner
- Tighten the Phillips screw in the door handle
- Connect the master switch panel wiring harness
- Push the master switch panel into place
- Tighten the Phillips screw in the door pull
- Push on the door pull trim piece
- Push on the door handle trim piece
- Push on the sail panel
Tools needed
-
Flat Blade Screwdriver
Phillips Head Screwdriver
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, my name's Mike Green. I want to help you save time and money repairing your vehicle. I have 20-plus years experience restoring and repairing cars and trucks. My company, 1A Auto, sells high quality replacement parts over the internet. In this video, I'll be showing you how to install these parts. By the end of this video, you'll know how to install them and where to get them. That's going to save you time and money. Thank you and enjoy the video.
In this video, we're going to show you how to remove and then replace the door panel, drivers side front door panel on this 2005 Camry. The only tools you'll need are a flat blade screwdriver and a Phillips screwdriver.
To remove the door panel, first you're going to remove a series of screws. There's one in behind here, and you'll see me pry that out. Underneath here you can pry this rubber up and there's a screw under there. Pry off this little grommet and there's a screw under there, and then there's two screws at the bottom: one there and one there. Use your screwdriver; put it in the back corner pry up and out on that rubber piece here. Put it right in the back there. This plastic piece should come out and then this piece should just pry right off. We'll just speed it up here a little bit as I remove those three screws: the one up there, the one in behind the door handle, and the one down on the door pull. Up and off, your mirror has a little tab you push on with your thumb and pull out.
There's a tab right here, push on with your thumb and pull out. You want to make sure you reset this connector by pulling it all the way back. Fast-forward here again as I remove those two lower screws. Now that you've removed this panel, you're going to see a Phillips screw right down in here; remove that. You can just grab the bottom of your panel. Pull this little triangle right out here, pull the panel up and off. Now reach in behind here and you can pull your cables out and up and your panel comes off. Put the cable in, snap it in the green one goes on the bottom, clear one goes on top. Pull your harnesses up and through then lift the door panel up and down the sill. Make sure our harness is in through. It all goes in.
Our large screw, just fast-forward here again as I tighten up that large screw that holds that arm rest brace, and then the two screws up top behind the door panel in the corner and then the two screws on the bottom of the door panel. Now our switch panel, make sure you've pulled that back, snap it right in; mirror snaps right in. Front down first punch it forward and down and then another screw. Little rubber, and then up here this corner panel you want to pull this if this clip didn't come off with your trim panel. Take it off, squeeze it down as much as you can, and it clips on right here to the panel. Looks like I put it on backwards. The less bent end goes into the panel and this goes in, okay snaps on.
Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.
Difference Between Brake Pad Materials What Are Brake Pads Made Of Car Brake Pads and Rotors
Sue teaches you the differences in brake pad materials, and what it means for your application.
