How to Replace Cruise Control Switches 2002-08 Dodge Ram 1500
Created on: 2016-08-03
How to repair, install, fix, change or replace a damaged, worn out, faulty or shorted power cruise control switch on 08 Dodge Ram 1500
-
When working on the yellow airbag or SRS system's connector/harness, ground yourself to a metal piece of the vehicle first to avoid any charge
step 1 :Disconnect the Battery
- Remove the 10mm wrench from the negative terminal of the battery
- Let the battery sit disconnected for 30 minutes
-
step 2 :Removing the Steering Column Cover
- Remove the T15 Torx screws on the bottom of the steering wheel column
- Remove the T15 screw from the steering column tilt lever
- Remove the letter
- Remove the top cover of the steering column
- Remove the bottom cover of the steering column
-
step 3 :Removing the Air Bag
- Insert the key to run position
- Rotate the wheel to the 9:00 position
- Remove the 10mm bolts from the airbag
- Carefully remove the airbag out of the wheel
- Ground your hands on metal components
- Put gloves on
- Push in on the two tabs on the yellow connectors
- Work the connectors out of the air bag
- Disconnect the horn connector
- Place the air bag in a safe place away from static
-
step 4 :Removing the Cruise Control Switches
- Remove the Phillips screw from the switch with a Phillips #2 screwdriver
- Pull the switch out
- Lift the tab and disconnect the wiring harness
-
step 5 :Installing the Cruise Control Switches
- Connect the wiring harness
- Insert the hooks of the switch into the steering wheel
- Tighten the Phillips screw
-
step 6 :Reinstalling the Airbag
- Touch metal/ground your hands
- Put gloves on
- Match the connector color with the harness slot color on the air bag
- Connect the horn connector
- Press the airbag into place
- Turn the key to the run position
- Turn the wheel to 9:00
- Start both 10mm bolts to the airbag
- Tighten the two 10mm bolts to the airbag
- Re-center the wheel
- Remove the key
-
step 7 :Reinstalling the Steering Column Cover
- Insert the lower portion of the steering column cover
- Insert the upper portion of the steering column cover
- Tighten the three T15 screws to the lower cover
- Start the screw into the tilt lever
- Insert the tilt lever into place
- Tighten the T15 screw to the column lever
-
step 8 :Reconnecting the Negative Battery Cable
- Put the key in the forward most position
- Tighten the negative battery cable with a 10mm wrench
- If the airbag doesn't deploy, the repair was successful
Tools needed
-
T15 Torx Driver
No. 2 Phillips Screwdriver
10mm Wrench
10mm Socket
Ratchet
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to remove the steering wheel mounted cruise control switches in this 2008 Dodge Ram 1500. The items you'll need for this repair are a T15 Torx screwdriver, a 10 millimeter deep socket and a small ratchet, as well as a number 2 Phillips head screwdriver.
While your airbags are meant to be a safety device, if you are not careful when working on them, they can be very dangerous. Any time you are working on or around your SRS or airbag system—these can be identified with a yellow wiring harness or a yellow electrical connector to designate that it is an airbag system you're working with—be sure to disconnect your battery for at least 30 minutes to allow any charge left inside the vehicle in its modules to be drained.
Any time you go near one of those connectors or harnesses, ground yourself to a metal part of the vehicle to remove any static charge that may be on your body. Before working on any part of the electrical system, you'll want to use the 10mm wrench to remove the negative terminal of your battery and set it off to the side. After your battery has been disconnected for at least half an hour to make sure that all the charge is removed from your modules, remove these two T15 Torx screws from the bottom of the steering column cover, as well as the one underneath here, and the one on the back of the tilt lever. After removing the screw from the steering column tilt lever, pull the lever out, and pull apart the plastic cover on the column, and remove it.
Install your key, click it to the run position, and rotate your wheel to the 3 o'clock or 9 o'clock position. This will allow you to access these two large holes on the back side of the wheel, which will give us room to get to the 10mm bolts that allow us to remove the airbag. Going to use a deep 10mm socket and ratchet, remove those two 10mm bolts on the back of the wheel. Carefully remove the airbag from the column.
Be sure to ground yourself on some metal components inside the vehicle before handling any portion of the connectors on the airbag. Again, these yellow wires, the harness covers, designate that this is an SRS system we're working on. While the rubber gloves are an insulator, you do want to make sure that you always remove static charge from your body before touching the live triple connectors on the airbags. Push in on the two tabs, and work the connectors out of the back of the airbag. Be sure to remember which way they came out.
Looking at it this way, our black one's on the left, brown is on the right. Connector here for the horn. Once the airbag is out, you're going to want to place it in a safe place, away from any type of static or electrical charges, and, if possible, place it under a sturdy bench or somewhere that, in case of a deployment, would contain the airbag. Remove the key from your ignition cylinder to allow the steering wheel to lock into place.
Using a number 2 Phillips head screwdriver remove the screw retaining the cruise control switch onto the steering wheel. Lift this leg off of the tab, pull out, and flip it over to gain access to the connector. You'll have to lift up on this tab fixed to the back of the switch. Remove the connector, and remove your switch from the steering wheel.
If necessary, you can repeat this step on the opposite side to remove the other switch. Reconnect the cruise control switch connector, lay these hooks under the steering wheel here, and push this plastic piece over the tab. Reinstall your Phillips head screw.
Again, be sure to ground yourself before touching an airbag. On the back of the airbag, you'll see that one connector is brown, and the other is black. This corresponds to the color of the connectors coming out of the harness. Snap those back into place, as well as the green connector for the horn, at the top.
Reinstall the airbag and horn into the center of the steering wheel. Put the key in the run position, and turn the wheel to 3 or 9 o'clock. Reinstall your two 10mm bolts. Be sure to get both bolts started before tightening either one down fully.
Recenter your wheel. Remove the key. Reinstall the upper and lower portions of the steering column cover. Pop the gear selector cover back into place. Reinstall your T-15 screws. The machine screw, being the silver one, is going to go into the center hole underneath, otherwise, the rest of the screws are the same. It helps to get the screw for the tilt lever started a couple of threads before you install it onto the car.
Make sure that these two plastic tabs line up with the two holes on the actual lever, and go ahead and tighten that down. Install the key, put it in the forward-most or run position before reconnecting your battery. This ensures that if you've worked on anything in or around the SRS or airbag system, if the airbag has become shorted in some way, or is going to deploy, it will do so with you outside the vehicle.
With the key on, go ahead and reconnect your negative battery terminal. Vehicle's got power, and the bag didn't deploy, so we know our repair was successful.
Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.
