How to Replace Intake Manifold Gaskets 2009-19 Ram 1500

Hey friends. It's Len down in 1A Auto. Today I'm going to be showing you a job, it's going to be super fun. We're going to be doing intake gaskets on a 2016 Ram 1500 Big Horn. So here we go. We got the hood up, we're going to come over here. What we're going to have to do is we're going to remove this air intake system right here. So first, what I like to do is remove any electrical components to make sure that we don't put any tugs on any wiring. I'll just put it down and out of the way. We're probably going to have to move it again because we're going to have to relieve pressure from here.

But anyway, our next step, there's a clamp down here that holds the air intake system down to the intake right there. So I'm going to grab my little 8mm. If you have access to something like this with an extension, it might be helpful. If not, you can just try to get there. Either way, you're going to remove this clamp. We don't need to take it all the way off. We just need it to be loose enough to be able to get that air intake hose up off. You can also use a flathead screwdriver. It's all preferential. I like to use a socket. Okay.

I'm going to grab it, give it a little wiggle, comes right up. We'll take a peek inside. Just make sure that there's no dirt, debris, water, anything like that. And we want to make sure that nothing gets in there also. So if you end up dropping a nut or a bolt, make sure that it doesn't get in there. I'm going to grab a rag. I'm just going to cover that real quick. We're going to come over here, we're going to remove that. Some people say you don't need to cover it because the butterfly is closed anyway. You know, that's up to you. Why risk it, right? I'm going to come over here. I'm going to grab this hose and I'll try to wiggle it around, see if I can break it free. There we are.

Next, I'm going to relieve these clamps. If you have access to a small screen driver or even a pry bar of some sort or a screwdriver, you can go ahead and do this. Basically, we're just pulling the clamps away from the box itself. There should be one on the front, two on the side and one on the rear. I can't see it, but I'm just going to try to see if I can grab it. There we are. I'm going to grab this, I'm going to push it this way while lifting up and I'll show you why. Under here, there's these holes. In the other part of the box, there's little male ends, those go into this side. So that's the reason why I had to lift up and push over to slide those out.

Now we can take our system, we can remove it. We can also take a peek at this sensor while we're here. We'll just make sure that the connections aren't corroded or green or any funny color that they shouldn't be. Metal is always a nice color. You can look inside, you can see what the sensor is supposed to look like in there. If it looks like it's dirty, black, gunked up. You can either replace it or clean it with a special cleaner. That's a service for another day. I'll set this aside safely.

Next thing I like to do, some people won't say that you have to do this at all, but I do it. I'm going to get this air filter right out of the way. The reason for that is because while I'm working up here, if any dirt or debris falls in this part of the air filter, the air filter is not going to be filtering that. Because this is the side that the air comes sucked in through the air filter box right in through here. Comes up through your air filter, all these little things right here. They collect your dirt and debris. Anything that's on this side, that's just getting sucked up into your engine. Let's be safe. We'll put it out of the way.

I'm going to grab this cover. It's going to be very simple. I'm just going to lift up. There we are. On the rear, there's no things to lift up. That's kind of more of a pull out. So here we go. Show you under here. We got two rubbers. Those go on to a prong right here. And there's another prong over here. The reason why I had to pull out is because there's prongs on the backside and those go into the backside on the engine right there, or on to the intake, I should say. So we're going to set this aside. We'll move on to the next step.

Okay, so here we go. We get that removed over there. We're going to come over to the battery side, making sure that the key is in the off position or completely out of the ignition, preferably. We're going to come over to the negative battery terminal, which is the side opposite than the red. We're going to use a 10mm. We're going to turn this nut counterclockwise to remove the negative battery terminal from the battery and set it aside, making sure that it can't come free from wherever you put it and hit up against this negative.

Once you start removing this, you don't want to go off on, off on, off on, off on, a whole bunch of times. Basically, just take it off, get it away, keep it away. When it's time to put it back on, you might feel a little bit or you might see and hear a little bit of an arc. Don't get worried take it back off, and then try to go again. Just put it right on. Okay? Now we're going to be very careful making sure that the positive is completely covered. You don't want to touch anything, like from the negative to the positive. If you're using some sort of extension with a long ratchet or whatever you've got, and you bring this down and you touch the positive. Well, you're going to work arc it out, you're probably going to weld the two, all the pieces together, maybe you can get a little zap.

So I'm going to get my ... The reason why I'm removing the negative and not the positive ... Let me just get this off here real quick and I'll continue that. There we go. Set this right aside. Excuse me. The reason why I removed the negative and not the positive is because if I was removing the positive, and I happen to touch my ratchet on here, if it was longer, well then we're going to do the same thing is basically touching from here to here. I'm going to go like this. I might touch to a ground of some sort and which is going to cause an arc, possibly blow a fuse, mess up your electrical system, we don't want any of that.

Let's just be safe. We're going to go with the negative. Now there's no juice going to the truck. So you can go in and try to turn on your radio. You can do whatever you want. Sorry, your music is not going to work, you disconnected the battery. So here we go, we're going to move on to the next step. So next we're going to take the serpentine belt off. It's this right here, little rubber. You want to pay attention to the way that it's in here. If you have a cell phone, you can snap a picture of it or you can draw it if you're an artist, that's fine too. Or even just look at this video a couple times. I'm sure it'll show you how to do it. So here we go.

I'm not trying to put this little tool right here, which is basically just the same as a 3/8 ratchet. You can either use this tool or you can use a 3/8 ratchet. Since I paid money for the tool, I'm going to go ahead and try that. There's a little spot down inside the tensioner that this slides right into. Let me get this geared up. Now I can relieve pressure from the tensioner. Grab the serpentine belt and I just pull it down off the alternator pulley. Now I'm going to carefully relieve pressure of the tool so it doesn't come slapping up and slam my hands into anything. You want to be careful not to get into a pinch point.

I'm going to try to remove the tool. Notice my little piece of stuck in there, that's okay. Just going to get mad about it and see if I can break it free. I can even try to bunk it with my tool. It'll just fall and hit the ground, I'm sure. Which is okay. I got to hit it. Get out of the way. I want to lose it. Nice. All right. So now we're going to take the serpentine belt off. I'm going to come around this way. Basically, I'm just removing it from all the pulleys as much as I can see from this angle. And then I'm going to go ahead and I'm going to move my stool so I can get to the rest of it. Okay, let's see. All right.

So now what's holding this on is the fan clutch. This might be a little bit difficult for some people to deal with. But all I'm going to do, I'm going to take the serpentine belt, I'm going to push it in up behind the fan that's up inside here, being very careful. It's just plastic so it shouldn't cut me but there could be sharp edges, yours might be metal. You have any sharp edges, just please be very careful. Safety first. I'm just going to take it, I'm going to try to put it up and over the fan. Just like this while my hands are in there. I'm going to carefully spin the fan which will walk the belt down and around. I'm going to see if I can pull it. Let's see if this worked. Pull gently, of course. Now we've removed our serpentine belt.

So now we're going to remove the alternator in which our reg is still on there, can get moved around. There's a little plastic cover right here. Just push that down and out of the way. This nut right here, we have the battery disconnected, so we don't have to worry about touching this on anything. We're going to use a 13mm wrench or if you have access to a half inch, that would work as well. We're going to turn it to the left. Since I'm working from the front, I'm generally speaking, if I was taking it off, I would be coming from the other side here. I'm going to be working in reverse. So I'm going to be turning to the right. If you're like, Len said left, but he's turning right. That's because I'm working from the other side.

Just going to loosen it up. Remove this nut. That's what it looks like. Very nice. Put it someplace where I can find it. I'm going to remove this cable from the back of the alternator. Set it aside. The battery is disconnected so you don't have to worry about it arcing out. I'm going to take my small pocket screwdriver. There's a little red clip right here. This is a lock to this. So all I'm going to do is I'm going to stick it in, slide that just like that. It is very simple, I just separated it and pushed it. Now there's a little push button right here. I'm going to show you with a screwdriver right there. You can use your thumb, you can use a small screwdriver, wherever you got.

I'm going to hold on to the assembly or the little connector. Just going to use my small screwdriver, I'm going to try to push it in, wiggle this around. Now that I've got this disconnected, I'm going to look inside, look for any funny colors. When it comes to vehicles like this, you don't want to have any rainbow colors. So just look for the metal color. We'll set that aside so it can't get crushed or broken. Feel around. I don't feel any other connectors back there, so that's nice. Now we're going to go ahead and we're going to remove our two mounting bolts for the alternator.

To do that, we're going to be using a 15mm socket, and I'm going to be using a 3/8 ratchet, sorry. Just going to go ahead and turn it to the left. That feels good. Nice and loose. I'm going to try to come over here. Put it on the second one, it's hiding. Okay, little hide and seek. It's a fun game. Everybody played it. Hopefully. There we go. I get that loose enough. Now if we want, we can try to grab these by hand, continuing to turn to the left, counterclockwise. Remove that one bolt. There we are. Set that aside. This one's going to be a little bit harder for me to grab onto with my hands. See if I can weasel my hand in there and grab it. Yeah, looks like I can.

Apparently I'm a little bit of a contortionist, so that's kind of neat. I guess you kind of have to be to work on cars. There we are. There's the second bolt. If we want, we can compare them. They're both the same. So which ones which? Who cares? There we go. We can try to wiggle this, you're going to notice it's stuck. I'll show you why. Right over here, there's a little crush washer essentially. So when we're putting this back in, what we're going to do is this piece right here that's kind of almost rusty looking, we're going to try to push this into the alternator a little further and out this direction. That's so this falls in nice and easy. Then once we tighten this up, it's going to slide this piece back through the alternator and right up against here.

So for right now, what we're actually going to do is I'm going to grab a small pry bar or if you have a screwdriver, not this, something a little bigger and heftier because I've probably done this with my hand. I'm going to go right here. I'm going to try to pry it up, see if I can wiggle this alternator. Lift it up and out being very careful not to cut any of these lines right here. These are very important. So I'm going to grab that pry bar and we'll move along. So I got my pry bar. I could probably go with a longer one if I want to, but let's just go with the size that we need. I'm going to come under here, up against the alternator, and this is the alternator bracket. This is part of the engine really it kind of just mounts on. But anyways, it's strong enough to pry against.

There we go. It's lifting up fairly easily. Okay. That's as high up as it wants to go at that point. We could try to grab it, wiggle it, shake it, pull it out. If it doesn't come out, we'll have to stick our pry bar down in between here but let's try this first. I'm going to be very careful of any pinch points. I'm not going to grab right here where my ... This is going to move up and down and pinch me. Safety first. Let me see if I can wiggle. If it doesn't want to wiggle, like I said, we'll just pry it. It's trying. Here we go. Come on, baby. Yeah. I love it. And now we've removed our alternator.

Now we're going to move on to the next step where it's going to be a little bit of compressed air if you have access to it, or you can use a little broom. Essentially what I want to do is make sure I'm going my safety glasses, gloves, obviously. I'm going to take a little bit of compressed air and I'm going to blow along the top of my engine. The reason for that is, as you can tell ... Looks like there's a mouse in the house. While the cat's away, the mice are going to play, aren't they? All this. Anyway, we want to get this out of here because once we start getting everything apart, there's going to be openings going into the engine, we want to make sure that no debris can get inside.

So let's get as much of this out of here as possible. If you haven't covered this yet, cover it please. If you haven't removed your air filter because you're like, I don't want to do that extra step, Len. Remove it, please. Here we go. Safety glasses on. Use a little bit air. I'm just going to come all the way around. I'm not in too much of a rush so I can spend as much time as I want. I just want to make sure that everything's removed from the top that could fall down into the engine. Anything that falls in the engine could potentially cause engine failure, and then we're kind of wasting our time doing all this. So let's keep moving.

We get it all blown off. We got this right here that's going to be in the way to lift it up. So all I'm going to do, I'm going to grab it. Let's see if I can slide it out of this little tube that it's hanging out in. There we are. You can tell there's two different ends. You can't mix that up, right? All we want to remember is that when we put it in it goes this direction. And not, I don't know, like this, like a snorkel. It's not a snorkel. Okay, guys? Put it aside. So here we go. Now we're going to disconnect the fuel injectors. All right.

To do that, I'm going to lift up on this little red tab using my small screwdriver. If it doesn't want to pull up easy, just kind of work it. It's got to come up so you're going to have to do it. You can cry about it, if you want, but it's going to get done. Next what I'm going to do, I'm going to find this little push clip right here, which is underneath that red thing. Right here, okay. And I want to just push it in. Once you push it in, just hold your wires, give them a nice tug and twist. Each one that you pull off, you're going to always look inside. Make sure there's no funny colors. Okay? Pretty much every electrical connector, just do it. Okay.

We're going to do the same for all four. Going down the line, we're going to go over the other side of the engine, do the four on the other side, and we'll move on to the next step. Here we go. We're on the driver side now. There's a couple things in the way. We're going to have to remove this anyway. So all I'm going to do is I'm going to grab this hose and try to twist it. See if I can break it free from the break booster. I can't, I can try to use my small screwdriver. Once again, this tool is so handy. I'm just going to try to pry. If you need to use a little bit of penetrate, you could do that. Basically all I'm trying to do is just separate this hose from the sensor. If I can't do that, well, then I'll come to the engine side. Come on.

Here we are. Check the condition. If you see any tears, rips, cracks, just go ahead and order this part right here. You need this, this is vacuum. Goes from your intake, creates vacuum, going to your vacuum booster for your braking system, super important. So this is in poor condition, just replace it. Okay. Now that that's out of the way, we're come over. We're looking for our fuel injectors. Let's get back on track. So here's our fuel injector, that's going to be a little hard to get to, isn't it? Well, the good thing is they make these fuel injectors so they can pivot a little bit. So there we are, I can get a little bit better view. Let's see if I can come in somehow. Try to get under that red. I'm going to try to carefully lift it carefully. There we are.

I remember doing the other side. I remember the little push is right underneath that red. I'm going to pull. Nice. I'm just going to come down the line. Do the other three and we'll move along to the next step. Last one, looking upon the clip. Spaces on my fingers. There we are. Looks good. So we've got all the fuel injectors disconnected, we can try to push those wires back and out of the way. The same on the other side after we do this. I'm going to grab this right here. Feels where feels like it goes. Doesn't feel like that has to be disconnected. But we do have to get it unplugged from the intake. So if you want to just lift it should come right up. We'll just slide that out of the way, just like that. So that's going to be clear now. Got this hose, we want to make sure that we get this up and out of the way.

There's a little connector here, all it does is just slide over that. Sorry. Quick, quick about it. I'm going to see if I can remove this right here without trying to break any off with the intake. If doesn't come off with the pocket screwdriver, we'll just grab another tool. We'll come back to that in a second. While I'm still up here, just going to go ahead and go this way. I'm going to take a look at this connector. This is what it looks like. I can twist it. Okay, let's see how this puppy works. That up and out of the way. Now there's two prongs, one right here, one up there. What I'm going to do is I'm going to try to squeeze those in, and then back. So it's going to basically come out the backside. Okay.

So I'm going to go in. See if I can get a push back with just one. The next one. I'll try to use this pocket screwdriver and I'm going to do the same thing. There we are. So that just took the lock off this fuel line right here. Now when we pull on this, there's going to be fuel that comes out. So we're making sure that we're wearing our safety glasses, we're wearing our gloves. I'm just going to give it a little pull. Yeah, see, fuel came out, sprayed all over the place. I'm wearing safety glasses, I'm safe. My beard, it's going to smell a little bit like fuel later. That's okay. I'm a grease monkey. So there we go.

Come over to the top of here. There's another electrical connector. This one all I'm going to do, is there's a little prong right here in the center. I'm going to squeeze it with my thumb. A little wiggle. I can even give a little push, help it along. That's out of the way. We'll just check this. This comes over next back into where the intake is so we don't have to remove this. This comes up and over the intake but it's part of the fuel rail. The fuel rail is all mounted to the intake, so we don't have to remove any of those. So that's nice. Get all our little wires out of the way. I'm just going to tuck them underneath and between the wiring harness and the belt cover. This is the belt cover by the way.

I'm just going to see about trying to remove this one. It's going to be a little bit hard for you to see. Hard for me to see too because I'm trying to show you, but there's a little push pin right here. There's going to be one over there. Basically, we're going to squeeze those together. Try to lift this up. There we are. That's the lock. It's kind of like that one over there. A little different, but same general idea. Slide it right up and out of the way. I got another one of those little hook clamps. Just a little. See, just slides over. Goes over the hose. We've already established how that works, it's pretty easy.

Just going to keep moving the rag around. We're going to keep covering it back up as much as possible. It's okay if it comes off and you're, whatever. We'll just make sure it's cleaned up before we put it back together. Okay. So we've got this off. We've got wiring that comes up to here, we get this hose. So we'll do, let's see. See how this little clip comes off real quick. I feel like if I just give myself a little bit of slack with the wiring, squeeze on this. Let's see. This one's a fighter. It's okay. All I did, because I had a hard time squeezing on this to get to lift up just because the angle, maybe you can do it and that's cool.

But basically you squeeze. It lifts up this little flap right here. And that's the lock for it. Okay. If you can't, just come in from the backside like I did, try to weasel yourself in, in between the side of it and the connector and then just twist and pull. Okay. We've got an electrical connector, what do we always do? We check it. No funny colors. Looks good. Nice. We are cranking. We just need our little fork tool here, fork tool there. We'll move on to the next step. We've got our little forky tool, you can use whatever you've got, this is what I have and I like to use it. I paid good money for it. As you can tell, it's a little hard to take out, and that's just because all these little teeth right here. So it's just going to want to fight with you. Just keep trying.

You might want to just break it off, don't, because you need us to try to go back together so it can be secured. So just deal with it. Fight with it and win that battle. There we are. So we still got plenty of good teeth on there, so when we go to put back together, just kind of push right in. I'm not going to do it now because then I'm going to be fighting again. I'm going to move on to this side and do the same thing. Just try pry it out of there. Nice. Okay, we'll just set this aside so we don't lose it. We have to make sure everything we take off, we remember where it goes back in, okay? It's going to be hard to remember. We can do it. We're a team, you and me. All right. Let's get down ...

So next what we're going to do, we're going to remove this nut right here. It's a 13mm head. So I'm going to use a long 13mm socket 6-point with my ratchet. I'm turning to the left, obviously. I'm just going to remove that nut. Come on, baby. Getting close. There it is. Put it aside where I can find it. Now we're going to start removing our intake bolts. So here we go. Now we're going to remove our intake, plastic, so we have to go on a specific order. Okay? To remove it, we're going to start in the center here, we're going to go number one, which would be in front of this. Number two is behind it. Number three is actually this one right here.

Number four would be the one that's closest to the one we just took out originally, the first one. So this is number four. Number five, we're going to jump over here. Number six, would be ... Let's see if I can find it. It would be essentially the one that's the next one down. So I believe it's right about here. I can't see it from this view, but it should be right behind here. Okay. Seven, the far-forward, I guess, passenger side, far forward driver side. Now we're going to go far-rear, driver side, that's number nine. Ending with number 10 all the way in the back far-rear passenger side, okay? It's up to you if you want to go in that order. It's recommended to go that way because it is plastic intake. Installing it, you need to go in order. De-installation, you should go in order. I'm not going to say not to. You do you boo-boo. But we're going to go in order. Okay.

So I'm going to start with number one. Grab my tool, and we'll do it. So here we go. Number 10. That should do it. Come on, baby. A little moisture back there. Smell like fuel. Looks like oil to me. We obviously have some kind of oil getting in from up there. We'll check that out once we get this up. Now, when I was removing these, some of the bolts didn't want to come out fully. And instead of risking cracking the intake manifold, I'm just going to take the risk of lifting up with them still in the manifold. You want to make sure you pay special attention to the fact that they stay in there and they don't come falling off into the engine and down to any of the ports. We don't want anything to fall into these ports. Okay, guys? So just please pay attention.

I'm going to see if I can grab this and wiggle it. Okay, that's coming loose. Feels like maybe something might still be held up in the front here. So I'm going to take a look and I know exactly what it is. I get down. Pardon my crying because ... There we go. Look at this. We still have our AC lines attached to this bracket. So even though I'm lifting up on the intake, they're kind of getting held. And we have the bracket right here. So once we disconnect this, we're going to try to lift up on the intake, slide this out. If that doesn't work, we can go ahead and attach the bracket itself from the intake area, but hopefully we don't have to. So let's try without doing that.

I'm just going to try to get in here. I'm going to see what's holding it on. Okay, all right. I'm going to grab my small screwdriver like this, okay. There we are. I'm going to try to pull these out of there. These are your air conditioning lines. So you want to make sure that you don't mess around too much with these. You don't want to shake them around too much. Okay? If you take this cap off, underneath there, there's a little bell stem. We don't need to worry about that. That's not for us for today. But basically you want to make sure that you don't move these around too much and shake anything free. This is under pressure. All right? Wear your safety glasses just in case God forbid something bad happens. Because we are moving things around here.

I'm going to grab this bracket, I'm going to try to pull it off this stud and do it by hand, hopefully. There we are. Moves fairly easily. So that's nice. Feels like our intake is ready to come up. So now what I'm going to do is I'm going to climb up, I'm going to see if I can lift it up and out. And then hopefully there'll be somebody there to catch it on the way out. So here we go. Moment of truth, everybody, we're hoping that we disconnected all of our wiring. When I'm up in here, I'm making sure that wherever my feet are, I'm going to have to use them to secure myself while I'm lifting. So I want to make sure I'm not stepping on anything that's electrical or fragile or anything like that. So I found some pretty good spots to put my feet.

I'm going to grab this. I'm going to try to come straight up a little bit. Want to get this line out of the way. Right here. Let me see if I can ... I don't know, I'll put it over here. Wherever. Under my leg. I don't know. We'll see. Wherever. Here we go. I'm coming up. I'm paying attention to anything that's electrical. Sometimes you'll get a wire like this one, it's hanging on, doing a little fishing and wants to stay. But I said it's time to go. So, we're going to have to take a look. Looks like we got a couple things that are hanging on still. What I'm going to do is I'm going to take out this one bolt right here, right there. And then I'm going to disconnect this right here, and hopefully get all this wiring right out of the way. Okay. All right.

So here we go. Let's take this off right here. That just makes it so when we get this bracket down, we can slide it out in-between here and right out of the way. Okay. Now I'm going to come over here. We can see when we lift, we're getting a little tug on this wire right here. That goes down to the ECT sensor. So I'm going to remove the lock, which basically is just lifting it up like that. Right in the center, like always, there's a little prong, you push in. Slider right up. Electrical tech connectors, we like to make sure that they're nice and clean, right? Keep saying it over and over and over and over. That's how I was taught. So that's how I'm going to teach you.

Now we're going to remove this bolt head right here. It's a 13mm. You can do it while it's down low or you can do a while it's up high, whatever you want to do. This way is easier for me so I'm not bending over too much. There's our bolt. Set it aside. We've got our little bracket. It's almost ready to come out. We just need this one right here. Use our handy screwdriver again. There we are. Okay. Take a look. I'm going to use the same screwdriver. I'm going to come under here, lift up on that. I'm going to hold up the intake with one hand, pull this out. I don't need to say it, we're just looking. Okay, looks good.

We're going to take this, set it over and out of our way. So here's our holes, okay. These could be considered the holes of doom. If you drop anything inside there, you're going to be wishing you hadn't. So let's not. All right. Let's see what we can do about getting this puppy up. Feels like maybe we have one more thing maybe somewhere in the back holding us. Looking at that wiring harness back there, it looks like maybe there was a clip holding it in. So we're going to have to see about getting back there. Just pay attention. Nothing gets in here, okay? I'm going to say it again, you don't want to buy yourself an engine. All right.

So right here's where the wiring harness is connected to it. I'm just going to take my little fork and see if I could find it. I'm shooting blind here. Let's see if I could push it off. Grab it with my hand. There we are. That came free. I'm just going to feel around now. I got my little tool under here. It's going to try to lift that up and out of the intake. It's just a plastic intake. So we want to be careful. If you can't get it up and out, well, you're going to have to make a decision on what you're going to do. I'm just going to try my darndest here for the purpose of this video. But there's always a plan B and that's your prerogative.

Looks like it's almost up. So close. So, all I'm going to do is I'm just going to try to tap this and work it out. One go, it's lifting. Nice. Let's see if I can feel. Is there a sensor? Feels like a sensor of some sort. I'm just going to wing it. I can't see anything. Let's see if I can push in. There must be a push clip here. I'm going blind. I wish I had my mirror. I don't. Where is it. I think I feel it. I'm going to go worried about here, hope. Come on, baby. There. So there's the red lock. We're going to want to grab on to that. We're going to push it downward. That should move it out of the way and then we can squeeze. All right. Don't mind the cracked mirror because I looked at it earlier and, well, you see me.

So I got my little pocket screwdriver here, and I apologize about a three-hour long video. I'm really trying here. Working on a mirror is not the funnest. What I'm trying to do is I'm just trying to unlock this, which should be fairly basic, just pushing down that red. So I'm going to see if I got it down far enough to unlock that. Now I'm going to try to squeeze it in and pull the connector down. At least that's my plan. So I'm going to grab it. It doesn't feel like ... Here we are friends. This is our nightmare. Something this small and little. You don't want this to fall inside that intake. Right down into your engine. So I'm just going to put it someplace like the trash where I won't have to look at it again. Just kidding. I'm going to put it up with the rest of my stuff. And I'll seriously think about if I want to put it back in. I might not, I might just super glue a stupid thing.

But now, hopefully, there's a spot that I can squeeze on this thing. I know we keep saying round one, round two, round three, round four. I don't know what round we're on anymore. So let's just do it. Let's just do it. Abracadabra, man. Oh, my God. Here we go. Okay. I'm waiting for the applause everybody. Hey, everybody, it's allergy season, I got my tissues. I'm coming under here, we got our intake off. We want to take a look, look at this mess. This is ridiculous. Somebody lives here rent-free. I don't know. We're not going to deal with that. We're not going to take it.

What we want to do is make sure all these holes are plugged up. I'm going to use something as simple as a rag. And I'm going to make sure that it's something that wherever it is that I use is something that I can grab in case it goes too far in, I'll be able to grab it and pull it right back out. Anything we put in needs to come right back out. You want to make sure that no dirt, debris, acorns, whatever might be under there, and how much why, I don't know if it's an acorn to you, but it's an acorn to me. Maybe you call it a b-corn or a c-corn, who knows? I'm going to get these in there. I'm going to do all these holes the same. Then I'm going to take something as simple as a vacuum cleaner. I'm going to clean up somebody else's mess, and I'm used to doing that. I got kids. All right. I'm just going to vacuum it all up once I get these all plugged up, then we'll be all set to move along.

Al right, Winston, let's crank this baby up. Here we go. Get all our rags in there. That looks pretty great. We'll do it again in a minute. So now we can take this a couple different ways. We can go ahead with a razor blade. We can clean up all this and then clean it again with a rag once we get off the majority of this crud. Or we can stay right ahead and get to the task at hand of replacing our part. So, we'll get down, we'll make a choice, and we'll go from there. All right.

So we've got our intake, we've worked hard to taking it out. Now we want to work hard and making sure it goes back in properly. So go ahead and replace these gaskets. If you have access to them, you got a little bit extra cake, it's super important. Some people will say, well, I'm just going to clean these up. They look fine. Yeah, maybe they look fine, but maybe they're dry. Maybe they're brittle. Maybe they're cracked, and you just don't know. Then you're going to be doing this all over again. So you can watch my video again, that'll be nice. Make sure you like it again, too.

So I'm going to grab the gasket. Pull it out of here. I'm going to do the same thing, all eight of these. You'll notice that there's two other gaskets. There's one here. Little wonky looking one. It's kind of cute. This one right here, same thing, okay. So we're going to take all these gaskets out and then we're going to go ahead, we're going to take another rag or whatever you have access to, pour a little bit of parts cleaner. We're going to try to come up in here and just get off some of this crud. We don't want to spray stuff directly into here. Maybe you do want to, but you don't want to. Just spray it on the rag. Try not to breathe in the vapors, like I said before, and then just give it a little scrub. This is why, I'll just show you real quick.

It gets worse when you actually use some parts cleaner, you'll see. So here we go. I got one. Just going to go around. I'm going to do them all. All right. We got our little kit right here with a whole bunch of new ones. These are nice and pretty and are not hard. Get that puppy out of there. So we got all our gaskets. We can dispose of those properly. We want to make sure that they're disposed properly. We're going to take a little bit of our parts cleaner. We're wearing our safety glasses. We don't want to go like this up close to our face, spray it, it comes back, hits us in the face. Protect your eyes. Protect your hands. The stuff getting into your skin is no good. Getting into your eyes, really no good. Here we go.

Just going to spray some on there directly. Let's see about cleaning out some of this crud in here. Getting pretty nasty. Boy, oh boy. We have to turn the rag around here in a second. I think all I'm doing is spreading the goodness. So I use my nice clean white rag. I cleaned out all these. All right, as good as I could. I could have probably done a little better. People might look at and be like, you missed a spot. You know what, it is what it is. I tried. Okay. So I got all the gaskets out, I cleaned inside as good as I could.

I'm looking at all the fuel injectors, making sure that none of the holes look like they're plugged up. If it looks like they're plugged up or they're black, or anything like that, now would be the time to replace these. I mean, it really wouldn't be too hard. We've got it all out. You could do it while it's still in the vehicle. That would be okay too. But we're here. I looked at them, they look fine. Next, what I want to do is I want to take my razor blade. I'm going to go along here, keeping it flat. Just like this. The reason why I'm doing this is to make sure that there isn't anything that's stuck on the outsides that aren't on the inside that I just cleaned out. If there's like any big mounds of anything on the outside, that might keep this from sitting flash.

So even though I got nice, beautiful new gaskets in there and I just spent a little bit of money on them, and I want to make sure I did it right. If I have something that's sticking up in between here and the engine, it's going to hold it up in a way, and this won't make a proper seal. So, might as well just throw it in the trash. So we're just going to take our razor blade, we'll spend another minute, go like this. You don't need to press hard, you definitely don't need to go like this like you're trying to cut into it. We don't want to cut into it, we just want to skim across the top. Get off anything that might be there that isn't supposed to be there. So we'll just do this to all eight of these.

So here's the part that we're going to start installing all of our rubber gaskets. We've got two of these. They're both pretty much the same. You can see that if you turn them, they may be a little bit different, but they're generally the same. You can see the way they are, one sides a little bit bigger, and then the other side smaller. One side is a little bit bigger, a little bit smaller. So we just want to look at these, we're going to find the side that looks like it's a little bit bigger and a little bit smaller and work at it that way. I mean, they might look pretty even to you. And who knows, maybe they are actually pretty even. It might just be an optical illusion from where I'm sitting. But I'm just going to see if it fits. Nice.

Go down here. See if this one fits. Also nice. So now we're left with all these. Where do they go? You know where they go. They go right along here. We're just going to push these in. They have these little kind of bump outs on them. That's essentially just to kind of hold them. If you wanted to, you could try putting a little bit of silicone around these, just to kind of lube them up. It's really up to you. It's preferential. Do you need to, I would say no. If you want to, I'm also not going to tell you no, because you do you boo-boo.

What could happen if you don't have them all the way pressed in? Let's say, you go kind on that? Then you got a little flippy-do kind of just hanging out. It's not in. It looks like it's in but it's not. I'm moving along. I'm not paying attention. I'm in a rush. It's getting cold outside and dark. I grabbed this. I go put it up on the engine. Let's say somehow this thing even just stayed in like it is but I go to put it on the engine and it goes like this or it goes like this or goes anywhere but not where it's supposed to go. You can imagine what's going to happen.

We're going to suck air, dirty air straight into the engine. You won't even probably get to that point because as soon as you start it up, your check engine lights going to turn on. You're going to have a misfire like crazy. And the things probably just going to be spitting and sputtering and you're going to be crying because you're going to take this all back apart again. So now that we got them all in, we'll just go make sure that we haven't missed anything. We're just going to press all these in. Make sure that they look good. They're not twisted, bent, ripped, missing inside your scrap pile. See, that one kind of felt like it was coming out a little bit.

So now we can go ahead. If you have access to a razor blade, something along those lines, you can call it whatever you want. Basically, what you're going to do is making sure that you have our rags stolen here so we can catch whatever we can. We're just going to go like this. I'll show you what the razor blade looks like in one second. You'll see the reason why we did this. Look at that. Nasty, right? So if we didn't clean these up, and we left all this crud on there, we're going to go ahead and we're going to put our intake with our brand new gaskets on to this. With all this crud right along where the gaskets are supposed to ride. You have to ask yourself, how good of a seal it's going to make? I'll just answer it for you. It's not going to make a very good seal at all. That's just basic.

So we're going to do that to all of these. We're going to go around one, two, three, four, all the way around, it's going to take a little bit of time. You can take your time on it, you do want it to be clean. After you get the majority of this crud off, you're going to keep those in. Grab another rag, us a little bit of parts cleaner, whatever you have, put it directly on the rag. Make sure you don't inhale the vapors from it. It's very toxic, I'm sure. Doesn't matter what kind you get. I'm sure it's toxic. And then you're just going to take it and you're going to go around all these again, get it as clean as you can. Okay, everybody? We want to make sure these are clean. We need a proper seal.

If you have a little bit of a leak here, you're going to have air getting sucked into your engine that's not getting metered, it's not getting filtered. It's just going to be bad. All right. We want a good seal. So let's do this right everybody. Here we go. So I'd The whole razor blade thing. Went around everywhere. I made quite a mess about a little flakies and gunk drops. So now I get my vacuum out again. I'm just going to try to clean up my mess that I made. I'm like that. If I make a mess, I like to try to clean it up. So here we go. All right, friends. I got this all cleaned up. I vacuumed it up. I tried to pick up as much my mess as possible.

I'm going to take a clean rag. I'm going to use a little bit of parts cleaner. I'm going to put the parts cleaner directly on the rag and I'm going to clean up all the metal areas. I can even try to get a little bit inside here. Try to get up some of this crud that's down inside there with the parts cleaner. I'm not going to be talking at all while I'm doing this because I want to try to inhale the least amount of these vapors as possible. So essentially, more than likely I'm going to be holding my breath through the most of it. So, here we go. There we go. That's our last one.

Now we're going to take out our rags. Actually, let's leave those in for one more second. We'll just move these harnesses out of the way, make sure that everything is very clear of where the intakes going to be sitting down. We don't want to crush anything. When we're putting this intake down, there can be nothing between those gaskets/the intake and this engine block. So this looks pretty good. Just move these a little bit further, just for safety sake. I don't want to buy a wiring harness just to show you guys how to do this. There we go. Very nice. So we'll start taking on out rags.

I'm going to start the farthest one away and I'm going to work my way this way, only because once I open this one, and then this one as I go, I'm going to be flinging stuff out of these. So as I'm flinging stuff out, I don't want to coming back over here. So I'm going to go like this and try to pull it up and out. I'll just go right in the middle if I want or I can throw in the recycling bin, whatever you might have around. As we're pulling them up, we want to be checking to make sure that we're not flicking anything up on to hear. Any little bit of dirt that we just pulled up, we're going to need to make sure that it comes up and away from where the seals are going to ride.

There we go. Does it look good still? We can just grab a rag and we'll clean those up in a second. That one's a messy one. These rags are still fairly clean. I will go ahead and reuse these again. So I'll just set them aside and use one of my rags that I just pulled out. I'm just going to clean up the mess that we made. If we wanted to, we could take a peek down inside and look at where our valves are. This is kind of neat to look at really. I don't know if you're interested in that type of stuff or not, but you can see the valves. You can see down inside there. Basically, that's where your fuel and air mixture is going to go down into. It's going to get dropped down into the cylinder and your cylinder goes, bang. Now, that valve is going to do its job, isn't it? it's going to go up and down.

If it looks like it's very dirty or it has some kind of liquid in there or a lot of debris, you're going to want to try to clean it out. Let's say maybe you drop the bolt in there somehow. Well, you're going to want to get that out of there, okay? Very important. So just take a peek in all of them. If you see a little bit of dirt or something like that, use your discretion. It might not be too big of a deal if there's a couple little flakes. This one right here looks like it has more than a couple. You could do that if you're wearing safety glasses or use your compressed air.

If you want to do some sort of valve cleaning, you could probably do it at this point. This one right here, if it was mine, I might do something with it. But for the purpose of this video, I'm not going to worry about it. So what I'm going to do is I'm going to go ahead and grab the intake. I'm going to carefully bring it over here, making sure all those gaskets are safely installed onto the intake. I'm going to look at this again and just make sure I get all the dirt off here. I just blew into that and it just kind of made a mess everywhere. So just pay special attention to everything here. Details, details. This is such an integral part. You want to make sure that you have plenty of safe vacuum there. I'm going look inside. That one's nice and open. Nice.

So let's grab the intake, we'll move along. All right. So here we go. We have our intake. Just going to get it up here. Now what I'm going to need to do, I'm going to need to hold it up, try to get it over these AC lines, bring it down. I want to be very careful of any lines, gaskets, especially. We want to pay special attention, make sure when we were carrying this we did not drop any of these gaskets. If you dropped any, you look behind you. I got nothing, I'm doing alright, cool. So now that I got it up to this point, I'm going to climb up and hopefully I'm going to be able to lift this, finagle it into where it goes. And then we're going to start by tightening up these bolts just slightly to get it down. We'll go from there. So here we go, friends.

I'm up in here, again. I'm going to try to grab this. I'm going to try to just lift it up and try to do as minimal dragging as possible. I don't want to disturb those gaskets that I just spent all that wonderful time that I'll never get back installing. So I'm going to get this down. All right. Now once we get it down, so it seems like it's about where it's supposed to go, we're going to want to take our flashlight. There we go. That's closer. Perfect. I'm going to grab my flashlight. I'm just going to take a peek around as much of this as I can see, just to make sure that maybe this wire came loose and went underneath that intake and I've got a pinch right here or even up on there. I just want to make sure that there's nothing underneath there.

This is very important. We need to make a good seal. Just take your time. Do it right the first time. This side looks great. This actually it looks really good. So now we can just go ahead and start the bolts in. When we tighten these, we need to go in a very specific order and I'll go over that with you in a second. All I'm doing is I'm getting these started in. Basically, I want to just line up the holes. If you want to get them bottomed out, you can, but I would not bottom them out even to that point. I would just get them all started in first and we'll go from there. Okay, everybody.

So now we got all these started in, what we're going to do is we're going to go ahead and bottom them out. We're not going to tighten them in any way. We're just going to get it bottomed out, we're going to go in the original sequence that I showed you before. All right. Same for removing it. We're going to go here, number one, which is right in front of here. Number two, number three, number four, which would be the next one back. Yeah, right here, which is pretty much next to the oil filter, I mean oil inlet. Let's see. Number five would be up here. Number six would be this one right here.

We're going to move back down over here now to the far-forward one. 7, 8, 9, 10. So all we're going to do is just bottom them out and then we're going to torque them down. So don't go grabbing onto it and give it like a, I want to turn it. Just get it till your ratchet stops and that's it. Now we're going to torque them. So here we go. Okay, friends. We got our torque wrench out. We've got our 8mm socket extension. We're going to go to nine-foot pounds, or 12 Newton meters, whatever your torque wrench is able to do, go with that. You don't want to go more than that.

This is the plastic intake. You crank it down to 100-foot pounds, well, you're taking it into your own hands. Just going nine. That's what the manufacturer recommends, it's what their robots or whatever they used to put it together used. Getting there. There's nine. That's number one. We're going to continue in our specific order. Sequence. Get number two over here. I guess, I could have probably bottom this one out a little bit more but that's okay. Nine. Going number three. Four. I'm going to go up to number five, which is up here on the other side of this. Essentially, we're going from the center, working our way out. That's number five.

Number six is back here. See if we can find it. Grab my flashlight. Just minimal help. It's probably dying at this point. It's okay. Yeah, I can see it. It's right down in here. I might need to change up my extension, but we're going to see if we can get it to work. Nice. I'm turning these to the right. Okay. We're go number seven, which is the far-forward passenger side. Come over here. Great. I feel like Cookie Monster. Come back to number nine, which is the rearward driver's side one. Close, slow down. Got one more. It's the far rearward on the passenger side all the way in the back. Can't wait to get down off this engine. I don't about you. Close. So we did all those.

If you wanted to, you can go back around and do them a second time. It's not really specified to do so. So I'm not going to worry about it. Some people do. Some people don't. It's your preference. So now we can move on to the next step. So now we're going to put in some wiring harnesses. You can start from the front and work your way back. Me personally, I like to work from the back, work my way front. That way there, everything's still in my mind. What I'm connecting in the rear, and I'm not going to just start with the front and get all excited that I'm almost all done and forget about this stuff out back. I don't want to forget about anything. So here we go.

We've got this lovely connector, we remember this guy. We're going to call him Fred. We can call him Torin. We're going to get the little lock right here. We're just going to start it in. This lock was our ... This is what took the video an extra hour. So I'm just going to get it started. Once I get this pressed in, I'm going to go ahead and squeeze this lock up and in. If you wanted to, you could probably squeeze the lock up and in now and then try to get it in. But let's not do that. Let's just get this in. The connector is back there or the sensor's back there. I have the connector in my hand, obviously. So I'm just going to bring it back.

This should be facing backward, just like this. Not like this. It would be impossible to get the lockout in that way and it definitely won't go back in. So the lock faces back. We're going to get our hand back there, we're going to find the sensor in the back. We're going to kind of do this, we're hold on to the sensor, we're going to do this, pull this up and in. We're going to listen for the click. Now we're going to feel around, we're going to find this red lock with a finger and lock it. We don't want this falling off back there. It's going to be interesting to try to find it again some day. So here we go.

I'm just going to get this back here. I'm going to feel around. I'm going blind. I feel it. I'm losing my ladder. Typical, right. I'm going to need a little bit more slack, so I'm going to just pull this harness in further. See if I can grab it. Come on, Len. If only there was a little bit more space. Good thing I don't have big hands. Here we go. There it is. Yeah. I got the lock. Very nice. Give it a little wiggle. It's going nowhere. Perfect. We've got our little, can you see that little security thing, that's just kind of holds it secure. So there's a piton in the back, sticks out of the back of the intake, we're just going to slide that over. That holds it secure. So the harness can't wobble around too much, get caught or anything.

We're going to connect this one in. It's this big one. It's not this one, you can reach. We'll use the big one. No lock, put that in mind. Ready? Click, I heard it. Give it a little wiggle. That's not coming off. We're just going to come right down the line now. We've got our fuel injector locks on this side facing forward. Clip it in. We got our red lock, push it down. We're going to do that all the way down the line. Facing forward. Grab it, feels good. Once we get this in, we're going to go over the other side. We're going to start at the rear and work our way forward.

Double check, make sure there's nothing else unplugged over here. We can leave this off for now because we got to do a little bit up here still. We'll worry about this in a minute. We'll put it up even so we don't forget. That would be what we're going to be dealing with up in the front. So I'm going to move over the other side. So we have this connector. We didn't disconnect it. But we did disconnect it from the intake itself. The way that I did is it just slid out. So for my instance, I'm going to slide it back in. From my clip, lock it in. Just kind of look at it, analyze it. I'm just going to take a better look at it. Let's try spinning this around. Really I don't think it goes that way though. Of course, it does. Nice. All right.

So now we're going to go down the line, we're going to plug in all of our fuel injectors. We've got our little reds, those are all popped up. If they were squished in, you'd want to just make sure that you use a small screwdriver, put them in the unlock position. Grab my flashlight. Click, click, nice. Feeling around, seeing what else I might have unplugged over here. We got this, you remember this. We'll do this in a minute. Let's continue with our connectors first. Another one. Locks up. It's already in unlock position. Click, click. Should be another one hiding out back here. Let's see if I can get my connector unlocked position. Click, click.

Last one's up here somewhere. There it is. My hand under here. Click, click. Give it a little tug, wonderful. Now we've a whole bunch of extra parts here. I like that. Falling back here, I can go ahead and connect in this fuel line if I want. I'm just put it on. Just like that. Actually, I'll pull it off and I'll show you something real quick. So this right here, the red is a lock. That lock needs to go on the bottom side of this grove right here, kind of like outward grove or whatever. Call it what you want. Anyway. Basically, we want to make sure we push this all the way down. So that groove meets up with the plastic part right here. And this lock is going to come on the bottom side or the fuel rail side of it.

We're going to try to push this in like that. So from the bottom side, lifting up, we get our two prongs that we had squeezed to push out in or out. Now I'm going to take this one, and that just locks those two prongs in the outward position. Give her a little tug. You're going nowhere. Perfect. All right, let's move along. Come over here. Take a peek. This looks good. Did all these, these, these. Perfect. So we are a little spider web of goodies here. This we remember, we had to bring it around this. That was the whole reason for disconnecting it. So I'm just come back over it like that. I'm going to get it over here. Yeah, just like that. Now I can connect this in.

This is a breather hose. This right here is your PCV valve. It's a very simple thing to change. You can check out our video on how to do that. I'm just put this over this. Squeezes in. I want to make sure it's bottomed out on there as good as it can get. You don't want to leave it just a little bit on. If it wiggles its way off, now you're have a vacuum leak. We don't want any vacuum leaks. That's what we just did all these gaskets and stuff for, didn't we? That feels good. We're going to make our way down the line, we did not unplug any of these coils. This looks good. All right. Looks like we can start working on the forward part of this engine.

Okay friends, here we go. We got a little tangled web right here. A bunch of little miscellaneous connectors. We're going to make sure that we get all these connected in where they go. They're all a little bit different. So you don't have to worry about saying, what if I switch them up? Well, you're not going to switch them up. And I'm going to help to make sure that you don't have to worry too much about it. I'm here for you. Just keep watching my videos and I'm going to keep showing you how. Here we go. This little thing right here, we remember that this held our lines. These are AC lines. These hold them secure so they're not moving around as the engine is shaken.

The bottom side of this bracket right here, I'm going to lift it up again so I can show you. Remember that this slides over that stud under there on the engine. So I'm going to get that onto that stud on the engine like that. Yeah. Now we've got this hole right here, that's going to line up with that for the bolt to go through that bracket. Very nice. So at this point, before I get too far into bolting anything down, I'm going to get these lines in here so I know that they're ready to go. We don't have to necessarily latch it in until we can at least get this lined up. Now we there, we latch it in on the lines where it actually belongs.

So there we go. I got that stuff lined up. I can go ahead and latch this in if I want. Just like that, just clips right in. You can a little hookie. We used our pocket screwdriver to release it. If you had to do it again, for some reason, we're just going to go straight here. Lift, release. So there we go. We've got our mounting nut that goes on that stud down there with a bracket slid into. We've got our mounting bolt, this is going to go through this hole, through our bracket and into the bracket on the intake. So we're just going to start these in, we don't want to tighten anything down yet. We also don't want to forget to tighten anything down. So let's try to work our memory a little bit here.

Those are all on. We're going to make sure we tighten those down. Do not forget. But let's do a little bit of connection action here. We've got this piece right here. Remember, this slid into the upper intake area. So I'm just bring it up. I'm going to get it where it belongs, making sure that I'm not tugging too much on any wires. Now that this is secured up here, it kind of gives us an inkling of where things are going to go. Because this one right here, this one doesn't reach all the way up to there. It just reaches right here. This fits pretty good. Let's make sure it slides in.

We've got our red lock. We already checked the connection. We made sure that it looked good. We're going to listen for a click. Nice. That one fits great. Good. These two little wires up here. This one goes right here. Click, click. Little tug, feels good. Tug, feels good. We got this one. You can either bring it up over the top or under the bottom and in. I'm going to go under the bottom, that way there it's protected by this bracket. Here's our lock. So on this one, the lock goes on the backside or the underside. And the slot right there has a little prong. Click. I heard it. Feel it, feels good. Feels good. We can go ahead and connect this if we want. Looks like our lock went down. That's okay. We remember how to do this, right.

I'm just going to squeeze these and lift it. Do it again, locks down. Oh no, squeeze them. Lift it, unlocked. Look inside, make sure that there's no real big debris in there or anything. If it looks like your gaskets are no good in there, you can replace them or replace this line. It looks good for me. And squeeze it in. Once again, we get the little line here. It's raised. We want to make sure that this lock goes on the inside edge of that, not on the outside here. You don't want just to put on like this and then lock it in. It needs to be all the way in, squeeze it, lock it. The lock needs to be on this side. Squeeze it in. Give it a little wiggle. There we are. For a tug, that's going nowhere. Love it. All right, we are cranking. Great job, everybody. Let's keep rolling.

We got a flow going here. This right here, we're going to wait on that. But if we wanted to, we can go ahead and put it right like this on to here. This comes from the backside, slides through. This is just a little breather. Goes down there, doesn't connect to anything, just hangs out. All right. Now before we forget, like we said, we want to make sure we tighten these two up. There's no torque specification form. So use your best judgment. You don't need to use a three-foot pry bar or anything like that and try to really get them crank down or a long ratchet, you just go ahead and use a regular ratchet. Same thing we used to remove it.

I'm going to come under using a 13mm socket. I'm going to get it bottomed out and give it just a little bit more. That feels pretty good. All we want to make sure is that we know in our minds that that will not loosen up again on its own. This one right here might be a little bit harder to get to. If you wanted to, you could use an extension. I'll see if I have one available. Maybe I could try this one, looks a little short. I wish I had a longer one here. I do have one, just not on me. But I'm going to give this one a try. I'm going to come in. I'm using a wobble extension or a couple of them. It just gives me a little bit of an angle, so that's kind of nice.

If you were torqueing something, you would want to not use a wobble extension, if you had another option, takes away from the torque. So I'm just going to get this on there. There we are. It feels good. This right here is a rubber mount, it's made to be able to move around a little bit. So as the engine is rocking and moving, it doesn't necessarily take these AC lines, rock and move them all around. Every time you rev engine, it's going to shake around, the motor mounts are going to do the best they can to keep it still. So a lot of horsepower in this puppy. It's still going to do some rocking. We want to make sure that these lines aren't getting ripped back and forth because they connect over here.

You can see that it connects right here to the body. So if this thing was yanking and it yanked on this, you're going to have issues. So here we go. We've got another electrical connector. What are we going to do with this one? This one's going to go to the intake right here. Okay. So now that we've got everything all put together, in exception of maybe just this right here, we're going to continue. We're going to make sure that we double check every single thing. Let's just take another look. If you have another minute. Pause this video. Take a look.

Make sure that we did not miss anything going around the whole engine. There's nothing else on the backside that we missed. There's nothing along the front here or alongside, I should say. We didn't miss a fuel injector, we checked all those. Got a double click on each one, click in and then lock. Same thing over here. Click and lock. Sounds good. We got our fuel plugged in. Got all our hoses like this. You get this one right here. This is going to come up. Remember, good thing we checked. This right here goes to where? I don't know. Right here. We took it off. We're going to put it back on. This is why we double check everything. It's easy to miss something, human error. We're only human. We're not dogs. We're not that good, right. All right.

So we got this stuff right here. We remember this one to the alternator. We can keep this set aside. This went to the air inlet hose. Keep this set aside. Tightened everything up. I'm along the front side. Everything feels like it's locked in nice and tight. All right. Let's move along. So we've got our alternator out. We're going to get ready to install it coming soon. What I want to do is these are where the mounting bolts came through, right here and right here. This is the nut side. What I want to do is I want to take these bushings, I'm going to spray them with a little bit of penetrant between the bushing and the alternator itself, both of them.

Once I do that, I'm going to take my punch, I'm going to go like this. And I'm going to take my hammer, I'm going to bonk it. I want to try to push these through a little bit, I don't want go all the way out. That's not what I'm going for. I'd like to at least get them pushed maybe a little bit closer to flush with the alternator. I'm going to do the same to both. That way there when we go over the bracket that's on the engine, this will be able to slide over nice and easy. Right now it's basically already pre-pressed in to where it's going to be up against. So it's going to make it very difficult to get this in lined up, you're going to end up whacking the alternator with a hammer, try to get a bang down.

This is just an easy step, it's going to save you a little bit aggravation down the line. Especially during install. See if I can get a little bit of this to actually spray out. There we go. A little bit there. You get some spray and you get some spray. I want to keep moving my cart across the room. I'm just going to take my brass punch. I don't want to use something metal, like something super hard. Because if you pin this over, you might have a hard time getting your bolt through it. All right. I just went with a brass punch, you can use whatever you've got. I'm just going to whack it down. Easy-peasy. I didn't try to knock it all the way out. You probably could. Don't bother. Don't waste your time. It's not what it's about.

We'll do this one. Turn it over. That feels good. Now this is ready for an install. If you wanted to, you can give it a check. Give it a spin. Listen for any funny noises. You hear something in there, you might want to replace it. If you hear a rattling, maybe whoever put it together or maybe something came apart, something's in there. But anyway, the spins good. I don't hear any whining or grinding or anything like that. So let's go ahead and install this.

So now it's time to go ahead and start getting ready to install our alternator. What we want to do is we're just going to double check. We're going to make sure that this is clean. If you want to, you take a little bit sandpaper or whatever you might have, rough it up. The other side, make sure it's clean, there's no rust, corrosion, anything. We'll double check in here. Looks nice and shiny, I can see some metal prongs, that's great. That's where it's going to make the electrical connection. If you saw a rust, you'd have to do something about it. It's a project for another video.

So I got these all pushed in. Right there. You're going to see what this does. When I come down and in, hopefully, there we are. It's going to slide right over this bracket. Nice and easy. I'm going to move this out of the way a little bit. See how easy that slid over the bracket. If I left those pins out and I didn't drive them back, then this would have had a much harder time. You probably would have been banging and hitting and cursing, it would have been a nightmare. So you're welcome, I showed you how to do that. So here we go.

I got this down here, moves around nice and free. I'm going to grab them two bolts. We remember they're both the same. So you can mix them up and play a little trick when your buddies, whatever you want to do. Anyway, they're both the same, whatever. Here we go. Slide it through. I'm just going to try to start it in. Just like everything else we've done so far, we have not tightened anything until we got the rest of the bolts that are part of that one unit in at the same time. Basically, if I tighten this up now before I put this in, I might not be able to move the alternator around. And if this hole isn't exactly lined up, I want to go ... Why?

Grab this. Get my hand in there, hopefully. Lift the alternator, I can do that. Get my hand back out. I'm just going to try to get it started. I'm going to try to use ratchet. So help me get in here a little bit easier. It's going to be a 15mm, grab that. I'm going to come under here. There we go. It's going in nice. I already have this one started. So while I'm on this bolt, if I want to, I can just go ahead and tighten it right down. What this is going to do is it's going to pull the nuts side of the bushing in and through and it's going to compress it up against this bracket right here. So you'll have a nice secure alternator.

Now, there's no real torque specification for this. So we're just going to bottom it out, and then just give it a little bit more, and then just a little bit more. We don't need to keep going after this. If you wanted to use, you could use a little bit of thread locker, that's your preference. For the purpose of this video, I'm not going to worry about it. Give our alternator a shake. That feels great. All right. Now we're clear to start connecting some stuff here. Now we'll run our belt. So we've got our connectors. I'm going to feel around. There's only two so we really shouldn't have too much of a problem. If we do, well, we got bigger problems, right?

Anyway, I'm going to get this in. That bottomed out. I've got my nut for the 13mm. Come right here. Put that down by hand. I'm going to snug it right up. Just grabbed my tool. Put it on my ratchet. Now for this, I don't want any real pressure. So I'm not going to use my long handle the ratchet and go all the way down at the end. Because even though it doesn't feel like I'm really pulling very hard, I have a lot of leverage here. With enough leverage, theoretically, you probably move the world. So I'm just going to grab it up close. That feels pretty good. Give it a little bit more if you want. We don't want to go too much, because that will break off internally inside of your alternator. And then you're going to be watching the video of how to replace this again or you can probably just remember because it's fairly basic.

We're going to take our little electrical connector cover. We're going to bring it around back. Drop it down there where we can barely find it. But I'm going to pull it up anyway. There we are. Click that in. Move these out of your way so you can see. We've got this right here. And listen for click, okay. There it is, we get our lock. Click, click. Tug, tug. Feels good. Push that over. We've got one more electrical connector, this goes up here like we said before. There we are. So now let's grab our serpentine belt and we're going to put that on there. We should be good to go and keep moving.

We've got our serpentine belt, new or old, whatever you're using. We're going to go back over the fan first. Remember, we had to take it off over the fan. Now we're going to go back over the fan first before we start running down any pulleys. So I'm just going to take it, see what I can do about getting it over, all the way around. There we are. So now we're into the pulley area. The whole belt is out of the fans route, we don't have to worry about getting caught. We're very careful not to get our fingers caught in there.

So now we need to try to think back to the way that we took this off. If you didn't draw a picture, take a picture. Whatever. Just watch this video, I'm going to show you how to do it. So I'm going to go over the fan pulley first, so we know that it goes over that. I'm going to take this, bring it over the tensioner and then back and over the crank. It's going to be hard to reach. Very hard to reach because I'm short. I'm going to climb up. Get my hand down in here. Being very careful not to cut myself. Safety first. Bring it up and over this pulley. If I lock that. That's okay. It's going to happen. It's going to keep falling off, you're just going to keep putting it back on. Keep your patience.

We have it approximately where we know it needs to go. I'm just going to double check where it's riding on the pulleys. You want to make sure it's sitting inside all the grooves on all of your pulleys. Like I said, it's going to keep falling off. That's okay. You don't mind. It's just part of it. It's part of the fun. Put this up on here. This up on here. Now I'm going to grab my tool and then we're going to make pressure with it or relieve pressure, I guess, on the tensioner. And then we're going to get our belt over the last pulley.

So we got our belts kind of laying over all our pulleys here. We got it for the most part inside all the grooves. We're going to recheck it. But right now what we're going to do is we're going to take our left hand, we're going to take this part of the belt and try to put it around this side of the smooth pulley. It's going to be difficult. We're going to need to push down on our serpentine belt tool or ratchet, whenever you're using, to relieve pressure from the tensioner and then we're going to try to work the belt along the outside of this and then over that. So the backside of the belt, it's going to go on the smooth side of this pulley. There we go. Good luck to you. Good luck to me. Let's do it.

Push down. Grab this belt. I'm just going to take a peek while I have the tension released. Looks pretty good. I'm going to come up nice and slow. You don't want to let that tensioner slap back. I'm going to try to get my tool off of there, completely. There it is. So now we're going to go ahead and connect in this hose, just goes right back here with the male end, and you get the rubber side that goes over to your air filter. So all I'm going to do, I'm going to try to wiggle it, slide it in. Perfect.

This just lays across the top of your engine, and it's going to come out through the slot that's inside the cover that we're going to be putting on in a second. So I'll just set it here for now and we can maneuver whichever way it has to go. I'll grab my cover. Get it up on here. Let's take a look at it. Nice and beautiful. We'll look over here. We've got two prongs and two rubbers. The prongs go into the rubbers that are on the top of the intake in the back there. These two rubbers that are on the cover, one goes here on this prong. One goes over here on this prong. I've got this right here, just comes up through here. So it makes it pretty easy to figure out where it goes.

On the top side, you'll notice there's a couple of arrows. These are so you can shoot a bull. Come right in. We're going to come in from the top at an angle. We're going to aim those arrows directly at those two rubbers back there. Try to work this in. Git it a little push if we need to. I'm going to look underneath. I'm going grab this, get it up where we need it. Now as we come down, we want to be trying to feel as we push, there's two rubbers that are up in here, they need to go under those prongs. We should feel it kind of like latch in a little bit. Oh yeah, that's beautiful. So we've got this lined up, we still got our rag here. We'll get our connector out of the way, bring it back up here so we don't forget about it under there, whenever. Now we'll move on to putting on the intake.

So here we go. Now I'm going to take this out. We're just going to take a double peek in there. Make sure nothing fell in there. There's no nuts, bolts, acorns, extra debris. You don't want to push on that butterfly, see if you can see inside there, there's nothing pretty in there to look at. Just don't push on it. We're just cleaning around it. Now what I want to do, I'm going to take my nice beautiful air filter that I took out. I'm going to put it back in. Should go into the box, come around here a second. That clip all the way. Nice. That looks great. Perfect.

We've got our air filter housing. Got out connector right here, that goes to here. This goes on to there. This goes on to there. These over these prongs. So here we go. Put it upon there. Going to make sure that it bottoms all the way up. I'm not going to tighten this clamp yet. I'm going to wait. I'm going to get everything else situated, then I'm going to tighten the clamp, and then I'm going to do this. We're going to do the electrical connector last. As we're shaking things around, we don't want to give this any tugs.

To do this air filter box. To put it back in, we're going to need to lift this part right here up, this part down, scoop it in over these knobs. Once you make sure you get all those in, and they are, now push down with all my might. Not really all my might but some of my might. I'm going to go ahead and I'm going to lock down all these clips right here. There's four of them, one, two, three, four. Sometimes the ones on the side can be very difficult, especially when you're coming from this angle. This one's the hardest. You'll have to bear with me. Got this right here. Just slides right on.

I'm just going to give this little wiggle, that's the whole box moving inside the rubbers. So that's good. It's supposed to do that a little bit. But we want to make sure that this part of the box does not lift up. If it lifts up, you probably missed your slots. If you don't get it in the slots, it's not going to make a good seal, you're going to be sucking dirty air past the air filter. So the air filter is going to be useless. It's going to come up in here and it's going to ruin basically everything we just did underneath there.

So now I'm going to come back around the front side of the engine, I'm going to go ahead and I'm going to tighten up that clamp. I'm going to use an 8mm with an extension and a quarter-inch ratchet. You can also use a flathead screwdriver, Flathead might slip a little bit, you're probably not going to get it very tight. I would just go with an 8mm, save yourself the hassle. Now we're going to take our little electrical connector and plug it in there. So I've got my little 8mm. Got swivel extension or swivel on my extension with my quarter-inch ratchet. We don't need very much leverage, we're not going all the way out here with a nice long ratchet. We're just going to snug up this clamp so we can't move the hose.

The hoses all the way down. We confirmed. You can get at this however you want to. You might not even need to use an extension and a swivel and all that stuff. This is just my preference. You do you boo-boo. Get this snug. Feels like it's getting snug. Just give it a little bit more. Should be pretty good. I'm going grab it. Wiggle it. If you can grab it, wiggle it and it pops right off. Put it back down. Tighten it up a little bit more. I'm going to take this. By the way, if you tighten up that clamp too much, and you feel it strip out, and all of a sudden it's not tightening anymore, you need to replace that clamp. Get them anywhere, but you need to replace the clamp. This needs to be tight. You do not want any dirty air getting past your air filter, getting sucked into your engine. Okay.

So here we go. Clamp. Click. There's no lock on that one. Give her a hug. We'll just double check all of our electrical wires here. Make sure nothing's flopping around, it can't get into the serpentine belt. We didn't leave any tools under here. We'll check all up along the cowl. I still get some stuff but I'm not there yet. But that's what I'm going to do. I'm going to double check everything now.

So now it's time to reconnect the battery. We remove the negative battery terminal to start our process. So now to end the process, we're going to connect the negative battery terminal. If you happen to see your battery terminals corroded, or if they look like they have a film of any sort on it, you can go ahead and use a tool that looks like this. This would be for cleaning the battery side. If you had a wire brush or something, you could try to clean inside there. Basically, what it comes down to is making a good connection between the battery terminal and the terminal end.

This one's in decent shape, so I don't have to worry about it. But if I did, I would just do this. Do that whole bunch of times, make it nice and pretty. Take off my cover, take my little wire brush. Do that a bunch of times, make it nice and pretty. I'm not going to worry about it. I just want to make sure that I let you know about that. If it is gunked up, dirty, corroded, doesn't look great, like it's going to make a good connection. Just go ahead and clean it up. And if this one's bad, well, probably that one is too. It couldn't hurt to have this one off still. Remove this one, clean that up, put it back on and then go back to your negative.

So here we go. We've got our 10mm. We've got our 10mm nut here. I'm just going to get a kind of close so I don't have to ratchet for days. Remember what I said, when we go to make this connection you might see and or hear a little arc or a spark. Don't be scared. Just connect in on. Don't put it on, jump off. Put it on, jump off. Just one time. You can do it. You're not going to get electrocuted. It's not going to cause you brain damage or anything, hopefully. I don't think California knows that it will. So let's go. Here we go. I heard it. Got a little snippet. Just going to go ahead and tighten this down. Should start feeling a little snug. As always, we'll give it a little wiggle. Feels great.

Thanks for watching. Visit one day 1aauto.com, your place for DIY auto repairs for great parts, great service and more content.