How To Replace Parking Signal Light and Bulb 2009-12 Chevy Traverse
Created on: 2014-01-18
How to repair, install, fix, change or replace a broken, damaged, cracked, faded, cloudy, or chipped signal light on Chevy Traverse, years 09, 10, 11, 12, and 13.
-
step 1 :Accessing the Parking Light
- Remove the two T20 Torx screws from the wheel well
- Remove the two T20 screws from below the bumper
- Remove the 7mm bolt from the wheel well
- Remove the 10mm bolt underneath the bumper
- Pull down the splash shield
-
step 2 :Servicing the Parking Light Bulbs
- Twist the bulb sockets out the light
- Pull the bulbs off of the socket
- Push on the new bulbs
- Twist the bulb sockets into the light
-
step 3 :Removing the Parking Light
- Remove the four 7mm bolts from the parking light
- Disconnect the parking light wiring harness
- Pull the light down and out
-
step 4 :Installing the New Parking Light
- Put the new parking light into place
- Insert the four 7mm bolts into the parking light
- Connect the parking light wiring harness
-
step 5 :Reinstalling the Splash Shield
- Put the splash shield into place
- Insert the two T20 screws underneath the bumper
- Insert the 10mm bolt underneath the bumper
- Insert the 7mm bolt in the wheel well
- Insert the two T20 screws in the wheel well
Tools needed
-
Flat Blade Screwdriver
T20 Driver
7mm Socket
10mm Socket
Slip-Joint Pliers
Ratchet
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we show you how to service the parking light bulbs as well as replacing the entire assembly on this 2012 Chevy Traverse. We show you on the passenger side, but the driver side is a similar procedure. The items you'll need for this are a flat blade screwdriver, a pair of pliers, a 7mm and 10mm socket and a ratchet, and a T20 Torx bit.
There are two T20 screws right in the wheel well, one there and one further down there, as well as two more T20 screws underneath. Remove all four of those. Now, you access the parking light through this panel right here. Just pull it down, pull it aside, and your parking light is right there.
To make it easier to show you, we're going to show you with the bumper cover off, but to service the bulbs, you just twist the socket out, pull the bulb right out, push the new bulb in, and twist the socket back into place. It's the same for this bulb as well. Push the new one in and just twist the socket back into place.
Now, to remove the entire assembly, you want to remove these four 7mm bolts. We'll just fast forward as Don does this, and once you remove all those, you just push the tab on the harness to disconnect it and pull the light down through that panel.
Then, you feed your new one up into place and replace those four 7mm bolts and then you reconnect that harness, and also replace the T20s underneath the bumper as well is that 7mm bolt in the wheel well and the 10mm bolt underneath the bumper. Then, replace those T20s in the wheel well.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Shop Products
2009-12 Chevrolet Traverse Front Driver & Passenger Side 2 Piece Parking Light Set DIY Solutions LHT05514
Part Details:
- 2 Piece
- (1) Front Passenger Side Parking Light
- (1) Front Driver Side Parking Light
How to Replace Front Lower Side Marker 1994-99 GMC K1500
How to repair, install, fix, change or replace a broken, damaged, cracked, faded, cloudy, or chipped signal light on 94, 95, 96, 97, 98, 99 GMC Sierra K1500
