How to Replace Water Pipe 2007-13 Mini Cooper S

Hi. I'm Mike from 1A Auto. We've been selling auto parts for over 30 years.

What's up, guys? I'm Andy from 1A Auto. In this video, I'm going to be replacing the water pipe in this 2007 Mini Cooper S. If you need parts for your video, click the link in the description and head over to 1aauto.com

All right. We're going to remove this hose right here. There's a little section right here that pulls up. Pull that retainer off and just slide that out. Disconnect this right here. Use a straight blade screwdriver. Loosen up this worm clamp, and we'll loosen up this one down below here. This goes to the turbo charger. Disconnect this connector right here.

There's a little lock here. Just pull up on that lock and slide it out. We're going to disconnect this hose right here. There's a little lock right here. Push down on that, remove that, so that's out of our way. We can slide this hose off here and slide it out of the way.

I'm just going to remove these four screws on the air box. Use a T-25 extension and a ratchet. Get those loosened up. They don't have to come out all the way. Then I'll disconnect this connector right here. Just push down on that lock. It's for the mass airflow sensor. We can grab the air box, rotate it, and slide it out of our way.

All right. I'm going to disconnect this intake tube right here. There is some little locks on it, so if you take a straight blade screwdriver, get underneath here, you can release it. Just rotate it a little bit and pull it out. We'll slide this up, and there's some locks on the front side. I can get in there from right here. Just slide underneath here and release these. We can pull this out. Just twist it and rotate it, and it'll come right out.

We're going to want to move these vacuum lines out of our way, so over here I'm going to get a small 90 degree pick and get under here. Try to loosen this up and then work it off just like that. Then over here, I'm going to take this vacuum line off as well, just use a different pick, and pull that off. We'll take these and set them aside.

I'm going to disconnect this connector right here just so I have more room to move the wiring harness around. Then also this little retainer right here that holds the wiring harness attached to the valve cover. Slide that up. You could use a pick tool under there or a screwdriver to help you move that around. Then I have a little more room to wiggle this harness around.

Now, I want to disconnect these two electrical connectors in here. You want to keep in mind which one goes where, because I believe that the connectors are the exact same. This one has one wire going in right here and this one has two wires. Just take a little pick, slide it underneath here, disconnect that connector and then also this one. Pull that connector out.

All right, so I'm going to take this connector out. There is a lock on the backside. That's why it's kind of hard to get out. I'm trying to push both locks at the same time. There we go. Slide it out. See, there's a lock on the other side as well. Pull that off and then there's a connector right here. Disconnect that as well. Just use another pick to release the lock on the connector and slide it off. Just get underneath there with the pick, and that just gives me a little more room with the wiring harness. You don't necessarily have to take these off to do this job, but it just makes it a lot easier. All right. I'm just going to attach a bungee to this wiring harness to move it out of the way, mostly for filming purposes. You could just slide it out of your way.

From underneath the vehicle, I'm going to drain the coolant. I'm going to drain it at this hose right here. There's no easy access port to a drain on the radiator. I don't believe there's an actual drain on the radiator, so we'll just loosen up this hose clamp. Just use hose clamp pliers, move it to the side. Make sure you have a drain bucket to catch the coolant. I'm just going to loosen this up and slowly drain some coolant out.

Now our coolant's drained out, I'm just going to hook this back up so I don't have to do it later. Take my hose clamp pliers. Now, if this hose clamp is weak, you're going to want to replace it with a worm style hose clamp, but this one's nice a strong so we'll just reuse that. That's good.

I'm just going to remove this coolant reservoir to get it out of my way. You don't necessarily have to do this, but then I'll have more room to work under here. I'll just take a hose clamp and remove this hose. I'll just take a pick, get underneath here and loosen this up. Take that hose off there.

I'm just going to take a 8 millimeter socket, extension, and a ratchet and remove this bolt right here. You can grab the reservoir. Sometimes this is a little tricky to get out. Just take a pick, get underneath here, and slide it forward. Slide that out like that. Pull it up. Actually I can just leave it out of my way like that.

Now I have more room right here to access this hose. I'm just going to use some hose clamp pliers. Take this hose clamp off right here. This is the upper radiator hose. It goes to the top part of the radiator. Now, once you release the hose clamp, it stays unlocked, just like that, so I'll just move that aside. You can just twist the hose back and forth and slide it off. You might have to have a drain pan underneath, because some of the coolant may still drain out.

Next I'm going to use this tool. We actually sell this tool at 1AAuto.com. It's a hose clamp pliers with a cable. When you tighten the cable, this tightens down this section. We're going to clip this onto the hose clamp over here and squeeze the cable. That's going to release the hose clamp. With it locked, I can actually twist the hose back and forth and release it. Once it's off, then I can release the tension on the pliers and move that out of our way.

There's a hose clamp underneath here that I'm going to have to get to. I can release this right here. Slide that back. I'll take these pliers again and take this hose clamp off over here. Just try to wiggle the hose and slide it off. I'm going to use this pick to try to slide the hose off. All right, take that off. A lot more coolant's coming out.

All right. This hose clamp is a little bit too close to this area right here. I'm just going to take a straight blade screwdriver, and just pry out on it a little bit just to try to rotate it just so we can access it easier. Then I'll use some hose clamp pliers and loosen it up. Squeeze that, move it aside, and slide this hose off. Just grab the hose and rotate it. Just to give me some room, I'm just going to take this piece off. I'm going to use some needle nose pliers, release this hose retainer right here, squeeze that. Then I'm going to take this and rotate it and slide it out.

Now I'm going to take this clip off on the back side. It's kind of hard to see. I'm just going to use a straight blade screwdriver. Get in there, and get underneath the clip. Slide this out. Just like that. You can pull it all the way out. Just going to use the 10 millimeter socket extension in a ratchet; take this bolt out right here. Loosen it up. Pull that bolt out and there's gonna be another one right here in the front. Loosen this bolt up. There's another bolt underneath here. If you need to, you can always references the new thermostat housing that you have and see where the bolts are. Oops, dropped it. Pull that bolt out.

Now, we're going to grab this housing and just rotate it back and forth a little bit. Try to slide it off. We still have the hose connected over here. I pulled the hose clamp off, but the hose is still connected. I'm going to take this pick and try to get that hose off. All right. That's disconnected. I can just slide this out. We're still connected in the back here. That crossover--I'm just trying to work it back and forth. I'm going to try rotating this a little bit. The O-ring is stuck and it's probably because it's been on there since the car was brand new. Just work this back and forth. Try taking the screwdriver and getting in between the housing and the crossover pipe. The housing is real brittle on this car, so I'm going to have to replace the crossover pipe as well. Disconnect that and pull it out.

Now we're going to pull this crossover pipe out. Just slide it out, just like that.

All right, now I'm going to show you where that crossover pipe goes down here. It's kind of hard to see, but if you keep going. Now, the water pipe is that little silver, round thing around the middle area right there. You can see that is where the crossover pipe goes. Now, there's a little piece of the pipe in there, so I'm going to actually have to pull it out. It's hard to show on film, but I just wanted to show you with the camera where it is.

Okay, I'm reaching my arm way down in the back there so that I can pull out some of the pieces that came off that water pipe. That's the O-ring and that's the pipe that broke. That's why we had a coolant leak. I got the other piece that broke off in there too. You want to try to get as much of it out as possible, because you don't want that stuff floating around in there. You can see this is where the O-ring would go and this is where those pieces would go on the pipe, just like the new one. There you go.

All right. I'm just going to take a piece of a sanding pad. You could use some sandpaper or some type of emery cloth or something. I just need to clean the edges because there is some corrosion on the aluminum. It's very hard to see, so I'm just going to show you with my arm down there. I'm just cleaning the surfaces where the O-ring's going to sit. Now I'm just going to take a rag and just clean that area. Again, you can't see this, but I'm just going to clean and get any of that stuff off so that the sealing surface is good for the O-ring on the new crossover pipe.

I'm just going to, before I install this water pipe, I'm going to just take a little bit of grease, a little grease on the O-ring. This will just make it easier to go in. Just make sure you use a grease that's going to work with coolant. It's going to help prevent it from ripping. We're going to slide this pipe down here. It's kind of hard to see. When we get the pipe installed in these locations, there is a couple wiring harnesses that their retainers are going to go through there. There's little Christmas tree clips. Those came out with the other one. Just install that, get it lined up. It's going to be tricky to do.

To help install this, I have this borescope that I have the camera aimed at the pipe and the hole where it's supposed to go. It's actually helping me be able to see down in there. We actually sell this borescope at 1aauto.com. See, that's the water pump right there and that's the housing on the outside. I'm trying to get the pipe to go right over the water pump.

All right, so I'm right there in that area, and that's where the pipe is going to go in. Pushing that pipe in. Now, there's a wiring harness that the pipe goes through the wiring harness, between the wiring harness and the engine block. Keep that in mind that you want to have that going in the correct way, because otherwise it's not going to fit.

When you're installing the pipe, this is the old one, you're going to want it in this direction so the pipe goes down. That makes a huge difference when you're trying to install it. The wiring harness is going to be on this side. There's a little clip that holds the wiring harness in there. I can't show it on video because it's too tight in there, but send it in there and just push it once it's lined up, and it should go right in.

Before I take the thermostat housing, I'm actually going to clean up the area right here where the gasket's going to meet. Just take a little sandpaper or some emery cloth and just clean up this area. Just take a little parts cleaner and a rag and just wipe this down.

I'll just take a little bit of grease and put it on this O-ring so that it goes in smooth. I'm going to take this, position this into the pipe like that. We're going to make sure that we get this pipe installed as well. We'll slide that on there first, because we never took that pipe off. It's just easier to not have to take that pipe off. Then get the O-ring lined up with the pipe, the water pipe. Get that lined up, and just wiggle it on. Okay, that slipped in, and that pipe's on down below here.

We're going to take these 10 millimeter bolts. Get them started. Just take a socket and extension. That's going to help me get the bolts lined up. I'll just take my socket, and extension, and ratchet, and I'll just snug these down. I'm going to use a torque wrench and a 10 millimeter socket. I'm going to tighten these down to 8 Newton-meters.

Now we're going to install this retainer clip. It's going to go over here. Just slide that in position there and lock it down in place. Okay, now we're going to resecure this hose clamp down here before we forget. Just take our hose clamp pliers, move that clip right there. Next we'll do this back hose right here, get this in position. Take this hose clamp pliers, squeeze that pretty tight. Just watch your fingers when you're working around the hose clamps, because sometimes they let go. That's in position, and release it.

All right. Next we're going to install this hose. This goes to the lower radiator. I'm just going to squeeze the clamp first and line it up. That looks good. I'll release. I can take this one. Now, this one was already locked, so this is that lock that I was talking about that sometimes if you tighten it too tight then it'll go into like an unlock mode. We can actually slide this one right on, and then we can release that. Sometimes you can take a pick. Sometimes you take a screwdriver, and then just try to rotate this.

I got it to release. I'm just going to move it into the right position. Just take the hose clamp pliers and just move it. We could use some needle nose pliers. That looks good right there.

Now we're going to take this bungee cord off and we'll move the reservoir. Get the reservoir in the right position, just like that. Take this hose, install the hose, and move the hose clamp. Take this bolt and tighten this down with an 8 millimeter socket, and extension, and a ratchet. Just snug.

All right, now we're going to move this bungee cord. This is going to go in this position. There's a couple little tabs on the bottom of this wiring harness bracket that slide into those little holes like that. Then on the backside there, there's a connector. We'll connect this connector down here and slide that in position there. Then there's this connector right here. Line that up, lock it in place. There's these two connectors that were the same connectors. The one with two wires goes over here. Lock it in place. Then the other one, the single wire, goes right here. I can connect the wiring harness right here.

Next, we're going to install this intake part of the air box. Just line this in position, push it in, and twist it. All right, now we're going to take this tube. Going to slide this down here. You're just going to have to twist it. Just keep twisting it. Get that in position, and we'll lock that in right here. That's good right there. Then lock it in over here. That's good right there.

One thing we forgot, to add these little hoses. They go underneath this air tube. Before we put everything back together, we can slide these underneath right here, just like that. Then this one's going to connect right here, just like that, and then this one's going to connect over here.

I'll take the air box. Line these three tabs up with the slots in the top of the air box, just like that. We'll take these screws. Get those started, and tighten these screws down. Snug those down. Before I put this on, I'll just connect the mass airflow censor right there. Then we can take this hose. This is going to go on this side, this intake tube. This actually goes down to the turbo down here. Slide that on there. When that's slid on, then we can take a straight blade screwdriver. Tighten this worm clamp down. We can do the same on this side.

We'll connect this connector right here. We'll connect this hose right here. Lock it in place. There's a little retainer that holds it right down here, just like that. We'll take this hose. It's going to slide onto the valve cover, just like that. Then there's this retainer that's going to hold that hose in there. Lock it in place.

Before we add the coolant, we're going to want to open up the bleeder screw. We'll just take a straight blade screwdriver, go down here, and loosen up the bleeder screw. Just a couple turns, not too much. Then we're going to take the appropriate coolant, and you're going to want a 50/50 mixture. Add the coolant. We'll just keep adding it until it starts coming out of the bleeder screw. You may hear some air coming out. Then once it starts coming out, you're going to close the bleeder screw. You just have to watch that. We'll just snug it up.

Now, we want the coolant level to be about where the level is. This is a little bit on the higher side. Then we're going to start it. I'm going to start the vehicle with the cap off, leave it running for a while, let the engine warm up, constantly monitoring to make sure that the engine is not overheating. I like the leave the heater on so that the engine. I can tell that the engine's full of coolant and the coolant's cycling, doing its thing. Then after about 10 minutes, the thermostat should have opened, and you can shut the vehicle off. Let it cool down, recheck your level, and adjust accordingly. Take it for a road test, and then adjust again when you get back, and you should be good to go.

Thanks for watching. Visit us at 1aauto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.

How to Replace Water Pipe 2007-13 Mini Cooper S

step 1 :Removing the Upper Air Intake Tube (Turbo)

step 2 :Removing the Lower Air Intake Tube

step 3 :Disconnecting the Wiring Harnesses

step 4 :Draining the Coolant

step 5 :Removing the Coolant Reservoir

step 6 :Disconnecting the Hoses from the Thermostat Housing

step 7 :Removing the Thermostat Housing

step 8 :Removing the Water Pipe

step 9 :Installing the Water Pipe

step 10 :Installing the Thermostat Housing

step 11 :Connecting the Hoses to the Thermostat Housing

step 12 :Reinstalling the Coolant Reservoir

step 13 :Reinstalling the Wiring Harnesses

step 14 :Installing the Lower Intake Tube

step 15 :Installing the Upper Air Intake Tube (Turbo)

step 16 :Refilling the Coolant

Tools needed

How to Replace Thermostat and Water Passage Housings 2003-07 Honda Accord

Same Day Shipping

Guaranteed To Fit

USA Customer Support

Instructional Video Library

How to Replace Water Pipe 2007-13 Mini Cooper S

step 1 :Removing the Upper Air Intake Tube (Turbo) 0:30

step 2 :Removing the Lower Air Intake Tube 1:30

step 3 :Disconnecting the Wiring Harnesses 3:00

step 4 :Draining the Coolant 5:41

step 5 :Removing the Coolant Reservoir 6:50

step 6 :Disconnecting the Hoses from the Thermostat Housing 7:48

step 7 :Removing the Thermostat Housing 11:18

step 8 :Removing the Water Pipe 14:07

step 9 :Installing the Water Pipe 14:16

step 10 :Installing the Thermostat Housing 19:06

step 11 :Connecting the Hoses to the Thermostat Housing 21:10

step 12 :Reinstalling the Coolant Reservoir 23:10

step 13 :Reinstalling the Wiring Harnesses 24:10

step 14 :Installing the Lower Intake Tube 25:40

step 15 :Installing the Upper Air Intake Tube (Turbo) 27:33

step 16 :Refilling the Coolant 29:30

Tools needed

How to Replace Thermostat and Water Passage Housings 2003-07 Honda Accord

Same Day Shipping

Guaranteed To Fit

USA Customer Support

Instructional Video Library

step 1 :Removing the Upper Air Intake Tube (Turbo)

step 2 :Removing the Lower Air Intake Tube

step 3 :Disconnecting the Wiring Harnesses

step 4 :Draining the Coolant

step 5 :Removing the Coolant Reservoir

step 6 :Disconnecting the Hoses from the Thermostat Housing

step 7 :Removing the Thermostat Housing

step 8 :Removing the Water Pipe

step 9 :Installing the Water Pipe

step 10 :Installing the Thermostat Housing

step 11 :Connecting the Hoses to the Thermostat Housing

step 12 :Reinstalling the Coolant Reservoir

step 13 :Reinstalling the Wiring Harnesses

step 14 :Installing the Lower Intake Tube

step 15 :Installing the Upper Air Intake Tube (Turbo)

step 16 :Refilling the Coolant